蝶阀厂家

莱克电动蝶阀的工作原理及结构与适用环境分析：

进口电动蝶阀的蝶板安装于管道的直径方向。在电动蝶阀阀体圆柱形通道内，圆盘形蝶板绕着轴线旋转，旋转角度为0°~90°之间，旋转到90°时，阀门则牌全开状态。 
电动蝶阀结构简单、体积小、重量轻，只由少数几个零件组成。而且只需旋转90°即可快速启闭，操作简单，同时该阀门具有良好的流体控制特性。电动蝶阀处于完全开启位置时，蝶板厚度是介质流经阀体时的阻力，因此通过该阀门所产生的压力降很小，故具有较好的流量控制特性。电动蝶阀有弹密封和金属的密封两种密封型式。弹性密封阀门，密封圈可以镶嵌在阀体上或附在蝶板周边。 
采用金属密封的阀门一般比弹性密封的阀门寿命长，但很难做到完全密封。金属密封能适应较高的工作温度，弹性密封则具有受温度限制的缺陷。 
如果要求电动蝶阀作为流量控制使用，主要的是正确选择阀门的尺寸和类型。电动蝶阀的结构原理尤其适合制作大口径阀门。电动蝶阀不仅在石油、煤气、化工、水处理等一般工业上得到广泛应用，而且还应用于热电站的冷却水系统。 
常用的电动蝶阀有对夹式电动蝶阀和法兰式电动蝶阀两种。对夹式电动蝶阀是用双头螺栓将阀门连接在两管道法兰之间，法兰式电动蝶阀是阀门上带有法兰，用螺栓将阀门上两端法兰连接在管道法兰上。

译文：
Electric butterfly valve wong principle and structure and applicable environmental analysis: 
Electric butterfly valve plate mounted on the pipe diameter direction. Electric butterfly valve in the cylindrical channel, disc-shaped disc around the axis of rotation, rotation angle of between 0 ° ~ 90 °, rotation to 90 °, the valve is fully open state licensing. 
Electric butterfly valve simple structure, small size, light weight, only by a few parts. And just rotate 90 ° to quickly open and close, easy to operate, while the fluid cool valve has a good feature. Electric butterfly valve in the fully open position, the disc thickness is only when the medium flows through the body resistance, produced by the valve pressure drop is small, it has a better flow cool characteristics. Electric Butterfly shells sealed and two metal seal type. Resilient seal valves, seals can be mounted on the body or attached to the disc periphery. 
Using a long metal seal valve life in general than the elastic sealing valve, but it is difficult to completely seal. Metal seals can adapt to higher operating temperature, flexible seal is affected by temperature limit of the defect. 
If you require the use of electric flow cool valve as the main choice is the right size and type of valve. Electric Butterfly structural principle is particularly suitable for production of large diameter valves. Electric Butterfly has not only been widely used in the oil, gas, chemical, water treatment and other general industrial, but also used in thermal power plant cooling water system. 
Commonly used electric butterfly valve has two wafer type butterfly valve and flanged electric motor. Wafer electric butterfly valve with stud connection between two pipe flanges, flanged electric butterfly valve is a valve with a flange with bolt flanged ends of the valve on the pipe flange.

 

 

执行器的工作原理

原文：
执行器的工作原理：
在齿轮级，发动机的转速可通过两套齿轮传送到输出杆上。主减速器由行星齿轮完成，副减速器由蜗轮实现，它被一套绷紧的弹簧固定在中心位置。在发生过载的情况下，也就是输出杆超过了弹簧的设定转矩时，中央蜗轮会发生轴向位移，对开关及信号装置进行微调，为系统提供保护。 气动执行器受由外部变化控制杆操纵的耦合的作用，输出杆在发动机工作时与蜗轮耦合，在手动操作时与手轮耦合。当发动机不工作时，可以很容易地断掉电机驱动，并且只需压一下控制杆即可连上手轮。由于电机驱动优先于手动操作，因此当发动机再次启动时，会自动发生反向动作。这样就可以避免当发动机运转时还开启手轮，有利于保护系统。由于手轮直接与输出杆耦合，因此可以保证在内部齿轮失灵或损坏时阀门的正常手动操作。
安装在齿轮上的开关与信号装置是一个密封外壳，保护其内部的元件实现以下功能：
(1)本地或远程显示阀门位置
(2)执行器/阀门的过载保护
(3)限定阀门行程范围

 (4)电气接口

气动执行器在不同型号阀门上的安装是通过输出杆来完成的，它可适用于现有的多种阀杆组态。

译文：
The wong principle of actuators:
In the gear level, the engine speed by two sets of gear transmission to the output shaft. Lord done by planetary gear speed reducer, deputy implemented by worm gear speed reducer, it is a tension spring is fixed in a ceal location. In the event of overload of cases, that is, the output than the spring setting torque, the worm gear axial displacement happens, fine-tuning, switch and signal device for for the system to provide protection. Pneumatic actuators to cool lever manipulation by external change coupling effect, the output shaft with worm gear coupling, when engine wong in manual operation with handwheel coupling. When the engine does not work, can be easily broken motor drive, and only need to press the cool rod is connected the handwheel. Because motor driven in preference to manual operation, when the engine starts, again will happen automatically reverse action. So you can avoid also open the handwheel when when the engine is running, is advantageous to the protection system. 
Due to the handwheel directly with the output shaft coupling, thus can guarantee the internal gear failure or damage to the normal manual operation of the valve. 
Installed on the gear switch and signal device is a sealed enclosure, to protect the internal components to achieve the following functions: 
(1) local or remote display position of the valve 
(2) actuators/valves of overload protection 
(3) limit range of the valve 
(4) electrical interface 
Pneumatic actuators on the different type valve installation is done through the output shaft, it can be applied to existing stem configuration.

 

 

进口软密封蝶阀蝶板的性能特点

原文：
软密封蝶阀蝶板的性能特点：
软密封蝶阀的蝶板安装于管道的直径方向。在蝶阀阀体圆柱形通道内，圆盘形蝶板绕着轴线旋转，旋转角度为0°~90°之间，旋转到90°时，阀门则牌全开状态。新型高寿命不锈钢蝶阀的特点以及蝶阀在使用过程中存在问题，本类阀门在管道中一般应当水平安装。软密封蝶阀根据连接方式可分为法兰式软密封蝶阀，对夹 式软密封蝶阀，焊接式软密封蝶阀。
1、流道通畅、流体阻力小;
2、动作灵敏、密封性能好;
3、使用寿命长、性能可靠;
4、阀瓣关闭快速，水锤压力小;
5、阀瓣行程短、关闭冲击力小;
6、软密封蝶阀整体结构简单紧凑、造型美观;
7、水平管道或垂直管道均可使用，安装方便;
8、结构长度短，其结构长度只有传统法兰止回阀的1/4~1/8;
9、体积小、重量轻，其重量只有传统法兰止回阀的1/4~1/20.

译文：
Features soft seal butterfly valve plate: 
Soft seal butterfly valve plate mounted on the pipe diameter direction. Cylindrical passage in the valve body, disc-shaped disc around the axis of rotation, rotation angle of between 0 ° ~ 90 °, rotation to 90 °, the valve is fully open state licensing. New high life features stainless steel butterfly valves and valve problems in the course of this general type valve should be installed horizontally in the pipeline. According soft seal butterfly valve flange connection can be divided into soft seal butterfly valve, wafer type soft sealing butterfly valve, welded soft seal butterfly valve.
1, the flow smooth, fluid resistance is small;
2, sensitive, good sealing performance;
3, long life and reliable performance;
4, valve closed fast, small water hammer pressure;
5, the valve stroke short, small closed impact;
6, soft seal butterfly overall simple and compact structure, beautiful shape;
7, horizontal or vertical pipes piping can be used for easy installation;
8, the short length of the structure, the structure of the traditional flanged valve length of only 1/4 to 1/8;
9, small size, light weight, it weighs only traditional flanged valve 1/4 to 1/20.

 

 蝶阀的作用及好处

原文：
蝶阀的作用及好处：

1、小巧轻便，容易拆装及维修，并可在任意位置安装。
2、结构简单、紧凑，操作扭矩小，90度回转开启迅速。
3、流量特性趋直线，调节性能好。
4、蝶板与阀杆的连接采用无销钉结构，克服了有可能的内泄漏点。
5、密封件可更换，且密封可靠达到双向密封。
6、蝶板可根据用户要求喷涂覆层，如尼龙或聚四氟类。
7、该阀可设计成法兰连接和对夹连接。

译文：
The role of the butterfly valve and benefits： 1、Small and light, easy disassembling and maintenance, and can be installed in any position.
2、Simple and compact structure, small operation torque, 90 - degree rotating open quickly. 
3、Flow curve tending to straight line regulation performance is good. 
4、Be used between the butterfly plate and the valve stem structure without pin, overcome the possible leak point. 
5、The seals can be replaced, and reliable sealing achieve two-way sealing.
6、Butterfly plate can spray coating according to user requirements, such as nylon or ptfe.
7、The valve can be designed as flange connection and connection to the clamp

 

 

进口金属硬密封对夹蝶阀的特点

原文：
金属硬密封对夹蝶阀的特点：
1、对夹式硬密封蝶阀采用三偏心密封结构，阀座与蝶板几乎无磨损，具有越观越紧的密封功能。
2、密封圈选用不锈钢制作，具有金属硬密封和弹性密封的双重优点，无论在低温和高温的情况下，均具有优良的密封性能，具有耐腐蚀,使用寿命长等特点。 
3、蝶板密封面采用堆焊钴基硬质合金，密封面耐磨损，使用寿命长。 
4、大规格蝶板采用绗架结构，强度高，过流面积大，流阻小。 
5、对夹式硬密封蝶阀具有双向密封功能，安装时不受介质流向的限制，也不受空间位置的影响，可在任何方向安装。 
6、驱动装置可以多工位（旋转90°或180°）安装，便于用户使用。金属硬密封对夹蝶阀的特点。

译文：
The characteristics of the metal hard seal butterfly valve to the clamp:
1, Wafer, hard seal butterfly valve USES the triple ecceic seal structure, the seat and disc almost no wear and tear, with functions of view more and more tightly sealed. 
2, Selection of sealing ring made of stainless steel, has the dual advantages of metal hard seal and elastic sealing, no matter in the case of low and high temperature, has good sealing performance, corrosion resistance, long service life, etc. 
3, Butterfly plate sealing surface using cobalt-based carbide surfacing, sealing surface wear resistance, long service life. 
4, Large size butterfly plate adopts the structure supporting structure, high strength, large flow area, small flow resistance. 
5, The wafer hard seal butterfly valve has two-way sealing function, installation is not restricted by medium flow direction, also not affected by spatial location, can be installed in any direction. 
6, Driving device can transfer (rotate 90 ° or 180 °) installation, making it easy for users to use. The characteristics of the metal hard seal butterfly valve to the clamp.

 

 

德国莱克（国际）阀门有限公司是流体控制领域的生产和供应商之一|亚太地区总部位于香港|公司致力于科研开发|生产流体控制设备系统德国莱克（国际）阀门有限公司主要产品有：蝶阀、球阀、截止阀、闸阀、止回阀、柱塞阀、针型阀、过滤器、金属硬密封蝶阀、波纹管截止阀、调节阀、刀闸阀、隔膜阀、旋塞阀、保温阀门、高温高压阀门、水利控制阀系列、食品专用等系列产品|驱动方式：有手动|蜗轮传动|电动|气动。阀体材料：铸铁,铸钢,不锈钢CF8,CF8M,CF3,CF3M公司产品的用户涉及石油、化工、电力、冶金、制药、食品、水处理、市政给排水、天然气、造纸、电子工业、楼宇、机械设备配套等领域。   德国莱克阀门（LIK）有限公司中国广州总代理|负责中国市场各项业务与技术支持中心|同时在中国市场销售。德国莱克（国际）阀门有限公司忠心欢迎中国客户同我们在中国各地的代理商及分支机构联系。 Germany Lik valve Hong Kong Ltd is one of the main manufacturersuppliers in fluid cool, The Asian-Pacific region general headquarter is located in Hong Kong , the company conceates efforts on the scientific research , producing fluid cool system.The main products of Germany Lik valve Hong Kong Ltd include: needle valve, butterfly valve, gate valve, globe valve, strainer, check valve, series products. Drive way: hand movement, worm gear drive , electric , pneumatic. Valve body material: Cast-iron, cast steel, stainless steelCF8,CF8M,CF3,CF3M. Company product consumer relates to petrochemical industry, electric power , metallurgy , pharmacy , food , water treatment , gas , paper making , electronic industry , the building world , machinery equipment forming a complete set.Chinese affair cee of the company is located in Guangzhou, it’s responsible for the markettechnical support,sell in China.  Germany Lik valve Hong Kong Ltd welcomes Chinese customers to contact with our agentsbranches in China

订购莱克阀门须知

1、根据使用场所、用途，且了解有关法规、规格、标准、方针、许用认可后既可选用适合各种要求的阀门；
2、确认阀门的工作条件、使用规格、适用介质、对应材质、操作方式、工作压力、介质温度；
3、确定与管道相匹配的公称通径：DN(mm)、NPS( " )；
4、确定与管道相连接方式：法兰式、内(外)螺纹式、焊接式、对夹式、卡箍式、卡套式等；
5、确定阀门操作的驱动方式：手动、蜗轮蜗杆传动、气动、电动、液动、电磁动、电液动等；
6、确认阀门的类型：球阀、闸阀、蝶阀、截止阀、止回阀、调节阀、电磁阀、安全阀、减压阀、疏水阀、针型阀、角座阀、隔膜阀、平衡阀、过滤器及其它特种阀；
7、确定阀门的使用形式：开关型、调节型、安全型、自动型、排放型等；
8、确定阀门壳体及内件的材料：碳钢、合金钢、不锈钢、球墨铸铁、灰铸铁、铜合金、铝合金、塑料等；
9、确定阀门的密封性能要求、密封等级或密封泄漏量；
10、确定阀门的防护涂层要求、包装要求、运输要求；
11、特殊需要的阀门还应确定：结构长度、阀门高度、外型尺寸、流阻、排放能力、流量特性、防护等级、防爆性能等参数；
12、确定阀门的安装位置及姿势。

德国莱克（LIK）阀门重视客户提出的每一个要求|并按照客户提出的要求量身定做|力求为客户提供的解决方案|同时也能优化产品性能|客户感到很满意且与他们保持紧密的合作关系。我们坚持这样做并取得了成功|这是我们发展的动力。自从德国莱克（LIK-VALVE）阀门诞生的那一刻起|我们就继承了德国传统的苛刻的制造精神|我们力求每一个环节都做到精益求精|所以我们的质保系统渗透到每一个工序|确保每个工人用到的是的零配件|这是我们发展的根本。

基于莱克（LIK）阀门业务在中国的发展和壮大|莱克集团于2000年在广州设立了个办事处|同年在香港设立亚洲总部-莱克集团亚洲有限公司。2003年设立了广州总代理|为国内客户提供更方便快捷的服务。同时莱克集团在中国的员工全部需要不定期的送到德国总部进行培训|因此他们能够运用先进的技术为国内客户提供高品质的服务。

一直以来|为用户量身定做|提供我们有竞争力的莱克（LIK）阀门解决方案是我们的目的和行动指南。我们长期关注市场并贴近客户|您完全可以信赖我们莱克（LIK）阀门品牌|及其专业的技术服务团队。我们的战略是集中全球优势满足当地客户的需求。

我们相信莱克（LIK）阀门能够为客户提供的价值！