上海韦米机电设备有限公司

0830100385气缸传感器 德国博世力士乐REXROTH压力传感器 气缸传感器

我公司现货供应博世力士乐（BOSCH-REXROTH）、阿托斯ATOS、派克Parker、迪普马DUPLOMATIC、油研YUKEN;本特利bentley、贝加莱B&R、西门子、光洋KOYO，美国ASCO，美国PARKER派克 等系列进口产品 

0830100385气缸传感器

传感器SIEN

尺寸：●4mm外径●6.5mm外径●M5外螺纹●M8x1外螺纹●M12x1外螺纹●M18x1外螺纹●M30x1.5外螺纹●块状

电压：10…30V，DC15…34V，DC20…265VAC，

●可选择PNP或NPN输出，●NC,NO或ambivalent触点，●齐平或非齐平安装，●切换距离大，●插头或电缆连接或端子连接，●带有两线的派生型号

特点：

●无机械磨损和撕扯动作，因此使用寿命长

●不会因灰尘或触点焊接在一起而出现故障

●无触点反弹，因此无切换故障

●切换频率高达3000Hz

●抗震

●安装位置随意

●颜色LED显示切换状态

●完全密闭，防护等级高

传感器测试器SM-TEST-1

用于测试和调节传感器和接近开关。方便调试和维护保养。

气缸上感应传感器作用

1、气缸上可以安装磁性开关或者其他开关量传感器，其作用是感应气缸的工作状态，使控制电路接收感应开关的信号即可作出下一步的动作。

2、例如：感应开关连接在TPC8-8TD型定时程序控制器的输入端时，可以作为到位停止、到位启动、到位启动紧急信号、不到位启动紧急信号等与位置有关的动作控制。

3、气缸的控制功能是有感应开关及控制器共同实现的，具体的功能可以通过功能设置表设置所需的控制功能，这样的组合可以实现各种控制设备的功能。

汽缸螺栓紧固的顺序不正确。一般的汽缸螺栓在紧固时是从中间向两边同时紧固，也就是从垂弧较大处或是受力变形较大的地方紧固，这样就会把变形较大的处的间隙向汽缸前后的自由端转移，较后间隙渐渐消失。如果是从两边向中间紧，间隙就会集中于中部，汽缸结合面形成弓型间隙，引起蒸汽泄漏。

气缸出现内、外泄漏，一般是因活塞杆安装偏心，润滑油供应不足，密封圈和密封环磨损或损坏，气缸内有杂质及活塞杆有伤痕等造成的。所以，当气缸出现内、外泄漏时，应重新调整活塞杆的中心，以保证活塞杆与缸筒的同轴度；须经常检查油雾器工作是否可靠，以保证执行元件润滑良好；当密封圈和密封环出现磨损或损环时，须及时更换；若气缸内存在杂质，应及时清除；活塞杆上有伤痕时，应变新。

0830100385气缸传感器供应型号

0830100300 SN4-R2-K03V-240 27 OHM

0830100304 SN4-R2-K05V-240 0,33 OHM

0830100310 SN4-R2-K03V-240

0830100315 SN2-R2-K03V-240 27 OHM

0830100316 SN2-R2-K03V-240 1,3 OHM

0830100317 SN2-R2-K03P-240 27 OHM

0830100318 ST6-R2-K03P-030 120?°C OHNE LED

0830100320 ST9-R2-K03V-030 OHNE LED

0830100325 SN2-R2-K10V-240 27 OHM

0830100326 SN2-R2-K00V-240 27 OHM 11M

0830100327 SN2-R2-K07V-240

0830100354 SN4-R2-K05V-240 1,3 OHM

0830100355 SN4-R2-K05V-240 27 OHM

0830100356 SN4-R2-K03U-240 27 OHM

0830100357 SN4-R2-K03U-240 0,33 OHM

0830100358 SN4-R3-K03V-042 27 OHM

0830100363 SN4-R2-K03U-240 100 OHM

0830100365 SN2-R2-K03V-240

0830100366 SN2-R2-K05V-240

0830100367 SN2-R2-K03U-240

0830100368 SN2-R2-K03V-240

0830100369 SN2-R2-K05V-240

0830100370 SN2-R2-K03U-240

0830100371 SN2-R3-K03V-042

0830100372 SN2-R3-K05V-042

0830100373 SN2-R2-K03U-240 100 OHM

0830100374 SN2-R2-K15V-240 VDE-AUFSCHRIFT

0830100375 SN2-PN-K03V-030

0830100376 SN2-PN-K05V-030

0830100377 SN2-PN-K03U-0,30

0830100378 SN2-PN-K10V-030

0830100380 ST9-R2-K03V-030

0830100381 ST9-R2-K05V-030

0830100382 ST9-R2-K03U-030

0830100383 ST9-R2-K05U-030

0830100385 ST9-PN-K03V-036

0830100386 ST9-PN-K05V-036

0830100387 ST9-PN-K03U-036

0830100390 ST9-R3-K03U-030

0830100396 ST9-R3-K05U-030

0830100400 SN5-R2-DA09-240 27 OHM OHNE LED

0830100410 SN5-R2-DA09-240 0 OHM OHNE LED

0830100430 ST6-NP-M08R-030

0830100431 ST6-NP-M08T-030

0830100432 ST6-R3-M12T-030 15 OHM

0830100433 ST6-PN-M12R-030

0830100434 ST6-R3-M08T-030 15 OHM

0830100435 ST6-PN-M08T-030

0830100436 ST6-R3-M08U-030 15 OHM

0830100437 ST6-PN-M08U-030

0830100438 SN3-PW-M012-30

0830100450 SN5-R2-DA09-240 27 OHM

0830100451 SN5-R2-DA09-240 6,8 OHM

0830100452 SN5-R2-DA09-240 0,33 OHM

0830100453 SN5-R2-DA09-240 1,3 OHM

0830100454 SN5-R2-DA09-240 100 OHM

0830100455 SN5-R2-M012-240 27 OHM

0830100456 SN5-R2-M012-240 1,3 OHM

0830100457 SN5-R3-M012-240 27 OHM

0830100459 ST9-R2-M008-24 1= 4=A

0830100460 ST9-R2-M008-24 1= 3=A

0830100464 SN2-R2-M008-030 STECKERBELEGUNG SIEMENS

0830100465 SN2-R2-M008-030

0830100466 SN2-R2-M008-036 100 OHM

0830100467 SN2-R4-M008-030

0830100468 SN2-R2-M008-030 PA

0830100469 SN2-R3-M008-036

0830100472 SN2-PN-M008-030 IMPULSVERLAENGERUNG

0830100480 SN2-PN-M008-030

0830100482 SN1-R3-M008-030

0830100483 SN1-PN-M008-030

0830100486 ST9-R3-M008-030 27 OHM

0830100487 ST9-PN-M008-036

0830100488 ST6-R3-M08R-030 15 OHM

0830100489 ST6-PN-M08R-030

0830100490 SN5-PN-DA09-026

0830100495 SN5-PN-M012-026

0830100496 SN1-R3-M012-030

0830100497 SN1-PN-M012-030

0830100500 SN5-PN-DA09-030 X, IMPULSVERL.

0830100502 SN5-PN-DA09-030 X IMPULSV. ROT-GRUEN-LED

0830100525 SN5-PN-M012-030 X, IMPULSVERL.

0830100534 SN5-PN-M012-030 X, SCHWEISSFEST

0830100606 SN1-R2-K03U-240

0830100607 SN1-R2-K05U-240

0830100608 SN1-R2-K10U-240

0830100610 SN1-R3-K05U-030

0830100611 SN1-R3-K10U-030

0830100612 SN1-PN-K03U-030

0830100613 SN1-PN-K05U-030

0830100629 ST6-R3-K03U-030 15 OHM

0830100630 ST6-R3-K05U-030 15 OHM

0830100631 ST6-PN-K03U-030

0830100632 ST6-PN-K05U-030

0830100633 ST6-NP-K03U-030

0830100634 ST6-NP-K05U-030

0830100635 ST6-PN-K00U-030

0842900300 STOP GATE VE 2

1020100000 DIAPHRAGM-TYPE CYL 80Q, 40H SA M12X1,25

1020200000 DIAPHRAGM-TYPE CYL 113Q, 50H SA M16X1,5

1020300000 DIAPHRAGM-TYPE CYL 160Q, 50H SA M20X1,5

1021100000 DIAPHRAGM-TYPE CYL 80Q, 40H DA M12X1,25

1021200000 DIAPHRAGM-TYPE CYL 113Q, 50H DA M16X1,5

1021300000 DIAPHRAGM-TYPE CYL 160Q, 50H DA M20X1,5

1022100000 DIAPHRAGM-TYPE CYL 60Q, 80H SA M12X1,25

1022200000 DIAPHRAGM-TYPE CYL 85Q, 80H SA M12X1,25

1022300000 DIAPHRAGM-TYPE CYL 250Q, 100H SA M24X2

1023300000 DIAPHRAGM-TYPE CYL 250Q, 80H DA M24X2

1025100000 DIAPHRAGM-TYPE CYL 80Q, 40H SA M12

1025200000 DIAPHRAGM-TYPE CYL 113Q, 50H SA M16

1025300000 DIAPHRAGM-TYPE CYL 160Q, 50H SA M20

1026100000 DIAPHRAGM-TYPE CYL 80Q, 40H DA M12

1026200000 DIAPHRAGM-TYPE CYL 113Q, 50H DA M16

1026300000 DIAPHRAGM-TYPE CYL 160Q, 50H DA M20

1027100000 DIAPHRAGM-TYPE CYL 60Q, 80H SA M12

1027200000 DIAPHRAGM-TYPE CYL 85Q, 80H SA M12

1027300000 DIAPHRAGM-TYPE CYL 250Q, 100H SA M24

1028300000 DIAPHRAGM-TYPE CYL 250Q, 80H DA M24

1301010000 CYLINDER 130DV/12/12

1301020000 CYLINDER 130DV/12/25

1301050000 CYLINDER 130DV/12/50

1302010000 CYLINDER 130DV/20/12

1302020000 CYLINDER 130DV/20/25

1302020030 CYLINDER 130EV1/20/50 SINGLE &

1302050000 CYLINDER 130DV/20/50

1302080000 CYLINDER 130DV/20/80

1303020000 CYLINDER 130DV/32/25

1303050000 CYLINDER 130DV/32/50

1305020000 CYLINDER 130DV/50/25

1305050000 CYLINDER 130DV/50/50

1305100000 CYLINDER 130DV/50/100

1320160002 SPARE PART KIT .

1320801000 ICM-DA-008-0012-0

1320802000 ICM-DA-008-0025-0

1320805000 ICM-DA-008-0050-0

1320808000 ICM-DA-008-0080-0

1321001000 ICM-DA-010-0012-0

1321002000 ICM-DA-010-0025-0

1321005000 ICM-DA-010-0050-0

1321008000 ICM-DA-010-0080-0

1321201000 ICM-DA-012-0012-0

1321202000 ICM-DA-012-0025-0

1321205000 ICM-DA-012-0050-0

1321208000 ICM-DA-012-0080-0

1321210000 ICM-DA-012-0100-0

1321601000 ICM-DA-016-0012-0

1321602000 ICM-DA-016-0025-0

1321605000 ICM-DA-016-0050-0

1321608000 ICM-DA-016-0080-0

1321610000 ICM-DA-016-0100-0

1322001000 ICM-DA-020-0012-0

1322002000 ICM-DA-020-0025-0

1322005000 ICM-DA-020-0050-0

1322008000 ICM-DA-020-0080-0

1322010000 ICM-DA-020-0100-0

1322012000 ICM-DA-020-0125-0

1322016000 ICM-DA-020-0160-0

1322501000 ICM-DA-025-0012-0

1322502000 ICM-DA-025-0025-0

1322505000 ICM-DA-025-0050-0

1322508000 ICM-DA-025-0080-0

1322510000 ICM-DA-025-0100-0

1322512000 ICM-DA-025-0125-0

1322516000 ICM-DA-025-0160-0

1323202000 ICM-DA-032-0025-0

1323205000 ICM-DA-032-0050-0

1323208000 ICM-DA-032-0080-0

1323210000 ICM-DA-032-0100-0

1323212000 ICM-DA-032-0125-0

1323216000 ICM-DA-032-0160-0

1323220000 ICM-DA-032-0200-0

1326108020 ICM-SA-008-0025-0-61

1326110020 ICM-SA-010-0025-0-61

1326112020 ICM-SA-012-0025-0-61

1326116020 ICM-SA-016-0025-0-61

1326120020 ICM-SA-020-0025-0-61

1326125020 ICM-SA-025-0025-0-61

1326216020 ICM-SA-016-0025-0-62

1326220020 ICM-SA-020-0025-0-62

1326225020 ICM-SA-025-0025-0-62

1327500000 PN-SPECIAL PNEUMATIC KNOCKER

1331201000 ICM-DA-012-0012-M

1331202000 ICM-DA-012-0025-M

1331205000 ICM-DA-012-0050-M

1331208000 ICM-DA-012-0080-M

1331210000 ICM-DA-012-0100-M

1331601000 ICM-DA-016-0012-M

1331602000 ICM-DA-016-0025-M

1331605000 ICM-DA-016-0050-M

1331608000 ICM-DA-016-0080-M

1331610000 ICM-DA-016-0100-M

1332001000 ICM-DA-020-0012-M

1332002000 ICM-DA-020-0025-M

1332005000 ICM-DA-020-0050-M

1332008000 ICM-DA-020-0080-M

1332010000 ICM-DA-020-0100-M

1332012000 ICM-DA-020-0125-M

1332016000 ICM-DA-020-0160-M

1332501000 ICM-DA-025-0012-M

1332502000 ICM-DA-025-0025-M

1332505000 ICM-DA-025-0050-M

1332508000 ICM-DA-025-0080-M

1332510000 ICM-DA-025-0100-M

1332512000 ICM-DA-025-0125-M

1332516000 ICM-DA-025-0160-M

1333202000 ICM-DA-032-0025-M

1333205000 ICM-DA-032-0050-M

1333208000 ICM-DA-032-0080-M

1333210000 ICM-DA-032-0100-M

1333212000 ICM-DA-032-0125-M

1333216000 ICM-DA-032-0160-M

1333220000 ICM-DA-032-0200-M

1420087022 SOLENOID COIL 24V-DC

1421000020 PILOT VALVE 24VDC /-30%

1421000070 PILOT VALVE 110V DC /-30%

1421007022 COIL 024DC-6W

1421007062 COIL 096DC-6W

1421007072 COIL 110DC-6W

1520210053 O-RING 9X2,5

1604009310 T.R.NUT SET 1600/40-50

1606009310 T.R.NUT SET 1600/63-80 64 PCS.

1610009310 T.R.NUT SET 1600/100

1612009310 T.R.NUT SET 1600/125

1620009310 SPECIAL NUT T R SET 1600/200 PU8

1670202000 167-DA-025-0025-DM00SCWS0S

1670205000 167-DA-025-0050-DM00SCWS0S

1670208000 167-DA-025-0080-DM00SCWS0S

1670210000 167-DA-025-0100-DM00SCWS0S

1670212000 167-DA-025-0125-DM00SCWS0S

1670216000 167-DA-025-0160-DM00SCWS0S

1670220000 167-DA-025-0200-DM00SCWS0S

1670225000 167-DA-025-0250-DM00SCWS0S

1670302000 167-DA-032-0025-DM00SCWS0S

1670305000 167-DA-032-0050-DM00SCWS0S

1670308000 167-DA-032-0080-DM00SCWS0S

1670309100 FRONTEND COVER KIT 167/03

1670309200 REAR END COVER KIT 167/03

1670309300 PISTON ASS. GROUP 167-032

1670310000 167-DA-032-0100-DM00SCWS0S

1670312000 167-DA-032-0125-DM00SCWS0S

1670316000 167-DA-032-0160-DM00SCWS0S

1670320000 167-DA-032-0200-DM00SCWS0S

1670325000 167-DA-032-0250-DM00SCWS0S

1670402000 167-DA-040-0025-DM00SCWS0S

1670405000 167-DA-040-0050-DM00SCWS0S

1670408000 167-DA-040-0080-DM00SCWS0S

汽缸结合面被蒸汽冲刷或腐蚀出沟痕，选用适当的焊条把沟痕添平，用平板或平尺研出痕迹，研刮焊道和结合面在同一平面内。汽缸结合面变形较大或是漏汽严重时，在下缸的结合面补焊一条或两条10—20mm宽的密消除间隙封带，然后用平尺或是扣上缸测量，并涂红丹研刮，直到消除间隙。此操作的工艺也很简单，焊前预热汽缸至150℃，然后在室温下进行分段退焊或跳焊。选用奥氏体焊条，如A407、A412，焊后用石棉布覆盖保温缓冷。待冷却室温后进行打磨修刮。

 

3842500080滑动轴承衬套GSM-1012-15 5S7 PC 1 1,49

3842500090压缩弹簧D-104 5SC PC 1 0,81

3842500097压缩弹簧D-187 5SC PC 1 1,21

3842500103压缩弹簧D-242 KUGELGESTRAHLT 5S7 PC 1 0,81

3842500106压缩弹簧D-264 KUGELGESTRAHLT 5S7 PC 1 2,02

3842500108压缩弹簧D-090V 5S7 PC 1 1,34

3842500114拉伸弹簧RZ-100 HI 5S7 PC 1 2,69

3842500120 O型环或3000600-N70A 5SC PC 1 0,94

3842500121 O形圈8,00-1,00S72NBR872 5SC PC 1 0,54

3842500122 O形圈8,00-1,60S72NBR872 5SC PC 1 0,67

3842500123 O形圈9,00-3,00S72NBR872 5SC PC 1 0,67

3842500134 O型环或1505200-N70 5S7 PC 1 0,32

3842500150活塞密封件523075 5SC PC 1 6,19

3842500151活塞密封523076 5S7 PC 100 456,24

3842500152活塞密封件523077 5SC PC 1 12,36

3842500153活塞密封件523078 5SC PC 1 6,05 5,58 5,46

3842500156轴密封圈G20X28X4 5S7 PC 1 9,42

3842500172装配螺钉-M6X8H8X12 5S7 PC 1 8,46

3842500181螺纹槽螺钉EJOT-WN1443-KA40X16 5S7 PC 1 0,29

3842500574铸件古斯泰瑞.F.218 711 5S7 PC 1 156,56

3842500575铸件格斯泰利.F.218 712 5S7 PC 1 156,56

3842500576侧墙部分GUSSTEIL F.218 713 5S7 PC 1 156,56

3842500577侧墙部分GUSSTEIL F.218 714 5S7 PC 1 156,56

3842500679 O形圈10,00-2,00S72NBR872 5S7 PC 1 1,87

3842500682刷子5X28 5S1件1 2,22

3842500729止推构件-5S7 PC 1 5,92

3842500737深沟球轴承61906-2RS1 5S7 PC 1 36,71

3842500738深沟球轴承6009-2RS 5S7 PC 1 42,13

3842500751卡环BR28 5S7 PC 1 2,02

3842500769凸轮滚子KR30PP 5S7 PC 1 35,25

3842500774履带支重轮NART8PP 5S7 PC 1 61,87

3842500805轴密封圈QFNP-6X12-AG01 5SC PC 1 18,04

3842500806轴密封圈QFNP-8X15-AG01-NBR 5SC PC 1 17,76

3842500808轴密封圈QHLP-12X22-AGU01 5SC PC 1 21,14

3842500809轴密封圈QHLP-16X26-AGU01 5SC PC 1 15,21

3842500810轴密封圈QHLP-20X30-AGU01 5S7 PC 1 10,49

3842500811轴密封圈QHLP-25X35-AGU01 5SC PC 1 16,68

3842500812轴密封圈QHWA-16X30X6/7,5-VGFU 5S7 PC 1 10,77

3842500813唇环PNIH-8X14,5X4-N01 5SC PC 1 5,52

3842500814唇环PNIH-20X26X5-N01 5SC PC 1 7,94

3842500815轴密封圈QHWA-25X35X6/6.5-NGFU 5S7 PC 1 12,92

3842500827保护帽D=8,8 5S7 PC 10,37

3842500834杆密封件E5 1015 N3578 5S7 PC 1 9,00

3842500835活塞密封523080 5SC PC 1 13,86

3842500836活塞密封件523082 5S7 PC 1 8,23

3842500837活塞密封件523084 5S7 PC 1 14,08

3842500864板螺母B51011VG3,9 5S7 PC 1 0,99

3842500865螺栓42 5S1 PC 1 3,27

3842500866螺栓57 5S7 PC 1 4,44

3842500877双槽环PDA-13X20-A01 5SC PC 1 7,68

3842500878双槽环PDA-18X25-A01 5SC PC 1 19,78

3842500879双槽环PDA-28X35-A01 5SC PC 1 8,35

3842500880双槽环PDA-43X50-A01 5SC PC 1 12,36

3842500881轴密封圈PEI-20X28X6-A05 5SC PC 1 6,85

3842500882轴密封圈PEI-30X40X6-A01 5SC PC 1 6,45

3842500884滑动轴承衬套GSM-0608-10 5S7 PC 1 0,94

3842500893衬套2550 DU 5S7 PC 1 7,41

3842500899连接插座09-0148-00-12 5SC PC 1 32,69

3842500902活塞430710 5S7 PC 1 37,94

3842500930连接插座09-0330-00-12 5SC PC 1 26,66

3842500953球面滑动轴承GE12C 5S7 PC 1 20,05

3842500977主梁BQ240 5S7 PC 1 42,77

3842500978主梁BQ320 5S7 PC 1 51,26

3842500979主梁BQ400 5S7 PC 1 48,96

3842500982安全带支撑轨BL160 L=34,7 5S7 PC 1 1,49

3842500984皮带支撑轨BL320 L=194,7 5S7 PC 1 2,42

3842500985皮带支撑轨BL400 L=274,2 5S7 PC 1 2,06

3842500986皮带支撑轨BL480 L=354.6 5S7 PC 1 3,90

3842501008定位条5X25X125 5S7件3,62

3842501009定位条5X25X205 5S7 PC 1 3,90

3842501010定位条5X25X285 5S7 PC 1 30,46

3842501011定位条5X25X365 5S7 PC 1 36,71

3842501012定位条5X25X445 5S7 PC 1 45,22

3842501069六角轴SW17X180 5S7 PC 1 50,45

3842501070六角轴SW17X260 5S7 PC 1 58,39

3842501071六角轴SW17X500 5S7 PC 1 106,13

3842501174胶带B=19 5S7 M 1 3,56

3842501176保护帽DI=13,5 5SC PC 1 0,54

3842501177保护帽ID=19,5 5SC PC 1 0,54

3842501226 ECCE9 18IC螺栓-5S5 PC 1 20,30

3842501227滚筒LFR50/8KDD 5S1 PC 1 35,26

3842501228定心螺栓D17 5S1 PC 1 0,26

3842501241接近开关BES516-324-E4-C-PU-03 5SD PC 1 67,35

3842501242接近开关BES516-324-E0-C-PU-03 5SC PC 1 109,79

3842501289杆-5S7 PC 1 40,15

3842501390锥齿轮Z=40 5S7 PC 1 26,80

3842501391锥齿轮Z=10 5S7 PC 1 33,35

3842501398主轴-5S7 PC 1 95,43

D3062，D301399驱动程序

3842501422保护帽ID=26 5S7 PC 10,53

3842501575夹爪搁脚板B和5S5 PC 100 182,90

3842501589对中销钉D7,3X21 5S1件100 52,32

3842501600制动曲线-5S7 PC 1 310,00

3842501601连接器58X90X104 5S7 PC 1 164,06

3842501639盘头螺钉ISO7380-M8X35-10.9-VZ 5S7 PC 1 0,29

3842501757制动曲线-5S7 PC 1 308,46

3842501759连接器58X90X182.5 5S7 PC 1 332,10

3842501960连接法兰HQ2/HQ2/U2 5S7 PC 1 283,85

3842502030凸耳凸轮-5S1 PC 1 1,49 1,36 1,33

3842502037针套10X14X14-2RS 5S7 PC 1 15,40

3842502095衬套3520 DU 5S7 PC 1 11,17

3842502167防护板DIN A5 DOPPELSEITIG 5S5 PC 1 6,88

3842502234六角轴SW17 L=124,5 5S7 PC 1 101,57

3842502259滑动盘D320 5S7 PC 1 159,52

3842502260齿带25T5/525 O E 5S7 PC 1 52,67

3842502266制动曲线-5S7 PC 1 164,06

3842502383锁紧垫圈S5-FST-MECH/ZN8CB 5S1 PC 1 0,12

3842502430楔块-5S7 PC 1 0,41

3842502446塑料切割螺钉EJOT PT-WN1413-KA40X和5S7 PC 1 0,29

3842502464滚筒3120125S7 PC 1 23,67

3842502587插入片DIN A5 DOPPELSEITIG 5S5 PC 1 3,58

3842502651盖管D25 L=10 5S7 PC 1 1,87

3842502699螺纹板10X25X72 5S7 PC 1 27,63

3842502852定位板ROHTEIL B=160 5S7 PC 1 94,84

3842502856定位板ROHTEIL B=320 5S7 PC 1 209,05

3842502858定位板ROHTEIL B=400 5S7 PC 1 337,81

3842502860定位板ROHTEIL B=480 5S7 PC 1 427,24

3842502861雨刮器-5S1 PC 1 0,28

3842502884转盘BG0 90GR.VORMONTIERT 5SC PC 1 366,14

3842502886转盘BG1 90GR.VORMONTIERT 5SC PC 1 497,55

3842502887转盘BG1 180GR.沃蒙特。5SC PC 1521,69

3842502888转盘BG2 90GR.VORMONTIERT 5SC PC 1 564,61

3842503059滑动齿轮装置GS 13-1 I=10:1 5S7 PC 1 559,21

3842503060滑动齿轮装置GS 13-1 I=15:1 5S7 

3842503061滑动齿轮装置GS 13-1 I=20:1 5S7 

3842503062滑动齿轮装置GS 13-1 I=30:1 5S7 PC 1 503,96

3842503063滑动齿轮装置GS 13-1 I=38:1 5S7 

3842503064滑动齿轮装置GS 13-1 I=56:1 5S7 PC 1 639,78

3842503068滑动齿轮装置GS 16-2 34:1 5S7 

3842503069滑动齿轮装置GS 16-2 48:1 5S7 

3842503070滑动齿轮装置GS 16-2 63:1 5S7 

3842503183衬套0806 DU 5S7 PC 1 2,76

3842503238轴D12X938 5S5 PC 1 28,33

3842503445外壳-5SC PC 1 156,75

3842503528插入板-5SD PC 1 185,27

3842503582异步电动机，3相220-415/50 440-480/60 

3842503583异步电动机，3相500/50 575/60 5S7 PC 1 225,50

3842503584异步电动机，3相440/50 500/60 5S7 PC 1 218,51

3842503585异步电动机，3相200/346/50 208-415/60 5S7 PC 1 217,67

3842503586异步电动机，三相230/400 0.12KW 

3842503587异步电动机，3相500 0.12KW 50HZ 4 5S7 PC 1 565,65

3842503588异步电动机，3相440/50 500/60 5S7 PC 1 296,57

3842503589异步电动机，3相200/346 0.12千瓦50赫兹4 S7 PC 1 492,68

3842503590异步电动机，3相220-420/50 

3842503591异步电动机，3相500/50 575/60 5S7 PC 1 268,40

3842503593异步电动机，3相200/346/50 208-415/60 5S7 PC 1 621,46

4257SC 342张紧辊

3842503670轴L=49,6 5SC PC 1 25,82

3842503705连接板20X44X139 5S7 PC 1 225,46

3842503706夹板-5S7 PC 1 94,03

D236,5X22活塞

3842503735活塞D29,5X22 5SD PC 1 2,85

3842503736垫片1X55,6X39,7 5SD PC 1 7,94

3842503759活塞D47,5X26 5SC PC 1 2,92

3842503760垫片1X81,4X58,6 5S

3842503764盖盖26X90 LE02 5S1 PC 100 578,59

3842503783异步电动机，3相230/400 0.18千瓦50赫兹4 S7 PC 1 269,93 249,71 242,94 229,47

3842503784异步电动机，3相500 0.18KW 50HZ 4 5S7 PC 1 310,84

3842503786异步电动机，3相200/346 0.18KW 50HZ 4 5S7 PC 1 339,42

3842503791钢板DRUCKAUSGLEICH 5S7 PC 1 31,25

3842503793齿带25T5/925 N V 5S7 PC 1 77,49

3842503839橡胶板H=10 5S7 PC 1 45,85

3842503898齿带25T5/925 A V 5S7 PC 1 99,14

3842503899齿带25T5/1070 A V 5S7 PC 1 112,46

3842503902直线滚子轴承KH3050PP 5SD PC 1 56,80

3842503919齿带25T5/595 N V 5S7 PC 1 59,19

3842503920齿带25T5/680 N V 5S7 PC 1 67,53

3842503921齿带25T5/785 N V 5S7 PC 1 73,58

3842503922齿带25T5/905 N V 5S7 PC 1 83,38

3842503923齿带25T5/595 A V 5S7 PC 1 68,74

3842503924齿带25T5/680 A V 5S7 PC 1 77,49

3842503925齿带25T5/785 A V 5S7 PC 1 86,37

3842503926齿带25T5/905 A V 5S7 PC 1 96,58

3842503927六角轴SW17 L=174 5S7 PC 1 82,73

3842503928六角轴SW17 L=254 5S7 PC 1 85,82

3842503929六角轴SW17 L=334 5S7 PC 1 89,98

3842503930六角轴SW17 L=414 5S7 PC 1 91,21

3842503931六角轴SW17 L=494 5S7 PC 1 94,03

3842504213外壳L=150 5SC PC 1 122,45

3842504632供气管D4 L=225 5SD PC 1 103,40

3842504633供气管D4 L=385 5SD PC 1 84,61

3842504635供气管D6 L=390 5SD PC 1 162,23

3842504636供气管D6 L=530 5SD PC 1 170,01

3842504637供气管D8 L=230 5SD PC 1 69,00

3842504638供气管D8 L=380 5SD PC 1 85,39

3842504645螺旋导线8X0,1MM2 L=1515 5SD PC 1 215,78

3842504657螺旋导线10-ADRIG 5SD PC 1 327,34

3842504659轴承座-5SC PC 1 2,02

3842504727杆头PP600 5SD PC 1 36,77

3842504728轴密封圈QFNP-4X8-AG01 5SD PC 1 14,10

3842504734导向柱D16X79,5 5S7 PC 1 46,95

3842504736安全盖SCHWARZ 5S7 PC 100 756,06

3842504745接近开关M8X1-BDG-PU L=600 5SD PC 1 118,13

3842504762定心螺栓D10/5 5S7 PC 1 0,11

3842504800定位板B=160 LT=160 5S7 PC 1 376,54

3842504801定位板B=160 LT=240 5S7 PC 1309,16

3842504803定位板B=160 LT=400 5S7 PC 1 390,00

3842504804定位板B=240 LT=160 5S7 PC 1 330,94

3842504805定位板B=240 LT=240 5S7 PC 1 473,68

3842504806定位板B=240 LT=320 5S7 PC 1 486,56

3842504807定位板B=240 LT=400 5S7 PC 1 392,13

3842504810定位板B=320 LT=320 5S7 PC 1 463,30

3842504811定位板B=320 LT=400 5S7 PC 1 661,71

3842504813定位板B=400 LT=400 5S7 PC 1 735,45

3842504843定位板LT160 B160 5S7 PC 1 299,98

3842504844定位板LT240 B160 5S7 PC 1 338,48

3842504845定位板LT320 B160 5S7 PC 1 351,92

3842504847定位板LT480 B160 5S7 PC 1 380,97

3842504848定位板LT160 B240 5S7 PC 1 337,81

3842504849定位板LT240 B240 5S7 PC 1 319,22

3842504850定位板LT320 B240 5S7 PC 1 366,85

3842504851定位板LT400 B240 5S7 PC 1 369,17

3842504852定位板LT480 B240 5S7 PC 1

3842504855定位板LT320 B320 5S7 PC 1 380,97

3842504856定位板LT400 B320 5S7 PC 1 395,92

3842504857定位板LT480 B320 5S7 PC 1 410,17

3842504858定位板LT320 B400 5S7 PC 1 448,92

3842504859定位板LT400 B400 5S7 PC 1 410,17

3842504860定位板LT480 B400 5S7 PC 1 425,93

3842504861定位板LT560 B400 5S7 PC 1 440,18

3842504862定位板LT640 B400 5S7 PC 1 454,29

3842504866定位板LT400 B480 5S7 PC 1 425,93

3842504870定位板LT720 B480 5S7 PC 1 483,35

3842504993止动盘D6,5 5S7 PC 100 378,02

3842504997烧结金属衬套16X20X20 5S7 PC 1 4,01

3842505127供气管D6 L=935 5SC PC 1 124,79

3842505128供气管D8 L=935 5SG PC 1 95,08

3842505176螺旋导线10-ADRIG 5SD PC 1 239,15

3842505256连接器插头09-0329-00-12 5SD PC 1 41,74

3842505341止动块21X21 5SC PC 1 1,34

3842505475双槽环PDA-10X16-A01 5SD PC 1 10,82

3842505476轴密封圈PNSP-6X11,2X5-A01 5SC PC 1 5,19

3842505604端板15X29,4X89,7 5SC PC 1 9,86

3842505607活塞D13,5X24 5SD PC 1 2,28

3842505608垫片1X26,2X24,5 5SD PC 1 8,43

3842505670直线滚子轴承KH1026PP 5SC PC 1 44,19

3842506065碟形弹簧242900 5SC PC 1 0,94

3842506095润滑油毡ERSATZTEILBAUGRUPPE 5SC PC 1 28,11

3842506160环-5S5 PC 1 0,66

3842506161密封套件-5S5 PC 1 184,69

3842506165滚筒312002 5S7 PC 1 16,12

3842506166 RUECKENGASFEDER 5S5 PC 1 46,45气弹簧

3842506171脚轮-5S5 PC 1 2,93

3842506199中间层ZU WERKZEUGSATZ 5S7 PC 1 23,82

3842506205阻尼元件D8X30 5SC PC 1 11,44

3842506207袖子-5S7 PC 1 10,17

3842506209箔材Hitzebestandig PE10 5S7 PC 1 24,74

3842506238紧固件套件M6X20 5S7 PC 1 8,34

3842506239紧固件套件M5X16 5S7 PC

3842506240盖D53X16 5S7 PC 1 4,82

3842506242插头-5SC PC 1 0,81

3842506289齿带25T5/410 O E 5S7 PC 1 45,87

S5，0649座板29HR1

3842506294深沟球轴承695-2Z 5SD PC 1 30,90

3842506296压缩弹簧D-051 5S1 PC 100 547,60

3842506297压缩弹簧D-143B 5SC PC 1 3,85

3842506306唇环PNAP-20X14X4,5-A01 5SC PC 1 9,82

3842506314快锁星锁5S5 PC 1 2,01

3842506319温度计-5S7 PC 1 67,39

3842506320唇环UNA1-14X8X4 5SC PC 1 4,85

3842506321唇环UNA1-16X10X5 5SC PC 1 11,31

3842506331拉伸弹簧Z-023I 5SC PC 1 4,59

3842506332密封件E5N780005 5SC PC 1 7,41

3842506374齿带25T5/720 N V 5S7 PC 1 62,99

3842506375齿带25T5/815 N V 5S7 PC 1 69,01

3842506376齿带25T5/840 N V 5S7 PC 1 70,64

3842506377齿形带25T5/880 N V 5S7 PC 1 73,31

3842506378齿形带25T5/930 N V 5S7 PC 1 74,51

3842506382齿带25T5/1150 N V 5S7 PC 1 91,73

3842506383齿带25T5/1240 N V 5S7 PC 1 103,06

3842506384齿带25T5/1280 N V 5S7 PC 1 100,50

3842506385齿带25T5/2040 N V 5S7 PC 1 151,43

3842506386齿带25T5/2080 N V 5S7 PC 1 148,51

3842506387齿带25T5/2440 N V 5S7 PC 1 183,72

3842506388齿形带25T5/2480 N V 5S7 PC 1 178,78

3842506389齿带25T5/3060 N V 5S7 PC 1 229,30

3842506390齿带25T5/4060 N V 5S7 PC 1 275,78

3842506391齿带25T5/6060 N V 5S7 PC 1 421,16

3842506392齿带25T5/570 A V 5S7 PC 1 66,45

3842506393齿带25T5/630 A，V 5S7 PC 1 68,46

3842506394齿带25T5/720 A V 5S7 PC 1 80,44

3842506395齿带25T5/730 A V 5S7 PC 1 81,93

3842506396齿带25T5/815 A V 5S7 PC 1 89,20

3842506397齿带25T5/820 A V 5S7 PC 1 89,20

3842506398齿带25T5/840 A V 5S7 PC 1 97,06

3842506399齿带25T5/880 A V 5S7 PC 1 99,10

3842506400齿带25T5/890 A V 5S7 PC 1 95,90

3842506401齿带25T5/930 A V 5S7 PC 1 99,14

3842506402齿带25T5/980 A V 5S7 PC 1 103,33

3842506403齿带25T5/1035 A V 5S7 PC 1 109,36

3842506404齿带25T5/1050 A V 5S7 PC 1 110,04

3842506405齿带25T5/1140 A V 5S7 PC 1 118,25

3842506406齿带25T5/1150 A V 5S7 PC 1 119,06

3842506407齿带25T5/1210 A V 5S7 PC 1 124,15

3842506408齿带25T5/1230 A V 5S7 PC 1 126,45

3842506409齿带25T5/1240 A V 5S7 PC 1 135,35

3842506410齿带25T5/1280 A V 5S7 PC 1 131,56

3842506411齿带25T5/1300 A V 5S7 PC 1 132,92

3842506412齿带25T5/1390 A V 5S7 PC 1 141,14

3842506413齿带25T5/2040 A V 5S7 PC 1 198,96

3842506414齿带25T5/2080 A V 5S7 PC 1 199,34

3842506415齿带25T5/2440 A V 5S7 PC 1 248,79

3842506416齿带25T5/2480 A V 5S7 PC 1 238,77

3842506417齿带25T5/4060 A V 5S7 PC 1 390,56

3842506421更换套件轮毂160 5S7 PC 1 122,43

3842506422更换套件轮毂=240 5S7 PC 1 122,43

3842506423更换套件轮毂=320 5S7 PC 1 129,95

3842506432齿带25T5/935 N V 5S7 PC 1 77,49

3842506433齿带25T5/1035 N V 5S7 PC 1 84,20

3842506479放气螺钉M8 5S7 PC 1 11,17

3842506498衬套0610 DU 5SC PC 1 2,96

3842506688车轮-5S5 PC 1 103,82

3842506689齿带25T5/570 N V 5S7 PC 1 52,99

3842506690齿带25T5/730 N V 5S7 PC 1 63,62

3842506691齿带25T5/820 N V 5S7 PC 1 69,40

3842506692齿带25T5/890 N V 5S7 PC 1 74,67

3842506693齿带25T5/980 N V 5S7 PC 1 80,44

3842506694齿带25T5/1050 N V 5S7 PC 1 85,01

3842506695齿带25T5/1070 N V 5S7 PC 1 86,37

3842506696齿带25T5/1140 N V 5S7 PC 1 90,95

3842506697齿带25T5/1210 N V 5S7 PC 1 95,90

3842506698齿带25T5/1230 N V 5S7 PC 1 96,58

3842506699齿带25T5/1300 N V 5S7 PC 1 101,30

3842506700齿带25T5/1325 N V 5S7 PC 1 103,33

3842506701齿带25T5/1390 N V 5S7 PC 1 107,75

3842506702齿带25T5/2125 N V 5S7 PC 1 164,96

3842506703齿带25T5/2525 N V 5S7 PC 1 192,42

3842506704齿带25T5/1325 A V 5S7 PC 1 143,19

3842506705齿带25T5/2125 A V 5S7 PC 1 218,88

3842506706齿带25T5/2525 A V 5S7 PC 1 256,62

3842506710轴密封圈C1-0013-N3571 5SC PC 1 7,13

3842506711槽环5X9X2,5 5SC PC 1 10,10

3842506714 O型环或10000300-N80 5S7 PC 1 1,87

3842506715 O型环或2000300-N80 5SC PC 1 3,24

3842506717轴密封圈10X20 5SC PC 1 28,40

VES5-1661止回阀SP761

3842506721活塞密封23X32X2,8氟橡胶5S7 PC 1 29,59

3842506828盖管D40 L=35,5 5S7 PC 1 24,23

3842506829盖管D40 L=75,5 5S7 PC 1 19,09

3842506830盖管D40 L=115,5 5S7 PC 1 24,90

3842506831盖管D40 L=155,5 5S7 PC 1 23,95

3842506833盖管D40 L=235,5 5S7 PC 1 31,76

3842506836盖管D40 L=63,5 5S7 PC 1 16,81

3842506837盖管D40 L=103,5 5S7 PC 1 18,57

3842506838盖管D40 L=143,5 5S7 PC 1 23,40

3842506839盖管D40 L=183,5 5S7 PC 1 20,17

3842506840盖管D40 L=223,5 5S7 PC 1 33,62

3842506842盖管D40 L=303,5 5S7 PC 1 46,68

3842506844盖管D40 L=383,5 5S7 PC 1 46,68

3842506845六角轴SW27 L=319,5 L1=169 5S7 PC 1 51,41

3842506846六角轴SW27 L=399,5 L1=249 5S7 PC 1 64,26

3842506847六角轴SW27 L=479,5 L1=329 5S7 PC 1 77,14

3842506848六角轴SW27 L=559,5 L1=409 5S7 PC 1 90,00

3842506849六角轴SW27 L=639,5 L1=489 5S7 PC 1 102,88

3842506851六角轴SW27 L=799,5 L1=649 5S7 PC 1 128,63

3842506853六角轴SW27 L=959,5 L1=809 5S7 PC 1 154,36

3842506854六角轴SW27 L=183 L1=169 5S7 PC 1 29,44

3842506855六角轴SW27 L=263 L1=249 5S7 PC 1 42,31

3842506856六角轴SW27 L=343 L1=329 5S7 PC 1 55,18

3842506857六角轴SW27 L=423 L1=409 5S7 PC 1 68,85

3842506858六角轴SW27 L=503 L1=489 5S7 PC 1 80,91

3842506859六角轴SW27 L=583 L1=569 5S7 PC 1 93,80

3842506860六角轴SW27 L=663 L1=649 5S7 PC 1 106,66

3842506862六角轴SW27 L=823 L1=809 5S7 PC 1 132,40

3842506866六角轴SW17 L=305 5S7 PC 1 49,06

3842506871六角轴SW17 L=705 5S7 PC 1 113,41

3842506873支柱型材60X90 2XM16K L=145 5S7 PC 1 50,85

3842506875支柱型材60X90 2XM16K L=305 5S7 PC 1 80,57

3842507112板32X773,5x173 5S7 PC 1 1.313,46

3842507757盖板管D25 L=4,5 5S7 PC 1 0,81

3842507758盖管D25 L=5 5S7 PC 1 1,08

3842507770齿带25T5/2180 N V 5S7 PC 1 174,48

3842508046盖管D25 L=117 5S7 PC 1 15,93

3842508151拉伸弹簧Z-072AI 5S7 PC 1 9,15

3842508783圆锥滚子LRG K/10 B=500 L=555 5S7 PC 1 241,21

3842508786齿轮电机380*50*550*4*48 5S7 PC 1 1.410,38

3842508787齿轮电机ODG 632T 250W GH14 5S7 PC 1 890,69

3842508866齿形皮带轮-5S7 PC 1 23,40

3842508912盖管D25 L=13 5S7 PC 1 0,81

3842508955连接板20X44X139 5SD PC 1 194,80

3842508957连接板25X89X228 5SD PC 1 282,49

3842509074反射镜888X539X472 5S5 pc1 380,36

3842509078 CO9 18OL装置MIT调光器5S5 PC 1 1.107,01

3842509144滚轮架。5S7 PC 1 39,60

3842509147板3X30X60 5S7 PC 1 17,75

3842509155齿带25T5/395 A V 5S7 PC 1 32,13

3842509400 O形圈17X2 5S7 PC 1 2,96

3842509652离合器。5S7件1 8,75

3842509773显示屏储物箱PK4130 5S5 PC 1 47,85

3842509861波纹管L=150轮毂=600 PLM60 5S7 PC 1 259,83

3842509862波纹管轮毂=450 PLM90-F 5SD PC 1 667,52

3842510025 ECCE9 18IC螺栓D20/D25 L=44,5 5S7 PC 1 13,73

3842510133回来。5S5件1 214,81

3842510244垫片17X17 5SC PC 1 0,28

3842510267金属板盖17/83/18X1 L=96 5S7 PC 1 15,33

3842510268金属板盖17/83/18X1 L=176 5S7 PC 1 20,51

3842510269金属板盖17/83/18X1 L=256 5S7 PC 1 25,31

3842510270金属板盖17/83/18X1 L=336 5S7 PC 1 35,78

3842510273金属板盖17/163/18X1 L=96 5S7 PC 1 25,41

3842510274金属板盖17/163/18X1 L=176 5S7 PC 1 39,77

3842510275金属板盖17/163/18X1 L=256 5S7 PC 1 46,15

3842510276金属板盖17/163/18X1 L=336 5S7 PC 1 50,99

3842510277金属板盖17/163/18X1 L=416 5S7 PC 1 49,19

3842510278金属板盖17/243/18X1 L=96 5S7 PC 1 35,78

3842510279金属板盖17/243/18X1 L=176 5S7 PC 1 50,99

3842510280金属板盖17/243/18X1 L=256 5S7 PC 1 53,68

3842510281金属板盖17/243/18X1 L=336 5S7 PC 1 71,44

3842510282金属板盖17/243/18X1 L=416 5S7 PC 1 62,57

3842510284金属板盖17/323/18X1 L=176 5S7 PC 1 53,68

3842510285金属板盖17/323/18X1 L=256 5S7 PC 1 62,57

3842510286金属板盖17/323/18X1 L=336 5S7 PC 1 82,06

3842510287金属板盖17/323/18X1 L=416 5S7 PC 1 91,89

3842510296金属板盖BL400 5S7 PC 1 27,17

3842510358同等零件套件UM 2/B 5S7 PC 1 910,33

3842510380星形椅腿-5S5件1 85,18

3842510381星形椅腿-5S5 PC 1 116,15

3842510382星形椅腿-5S5件1 72,21

3842510384垂直滑道-5S5 PC 1 9,74

3842510385垂直滑道-5S5 PC 1 10,14

3842510386垂直滑道-5S5 PC 1 10,80

3842510387辊-5S5 PC 1 16,28

3842510388辊-5S5 PC 1 18,03

3842510389滚轮LEITFAEHIG 5S5 PC 1 18,03

3842510391量规管-5S5 PC 1 23,50

3842510392量规管-5S5 PC 1 125,62

3842510393量规管-5S5 PC 1 27,39

3842510394量规管-5S5 PC 1 31,78

3842510395气弹簧-5S7 PC 1 132,71

3842510397斗式座椅-5S5 PC 1 160,89

3842510398座椅托架-5S5 PC 1 167,43

3842510399座椅托架-5S5 PC 1 171,15

3842510400座位-5S5件1 66,76

3842510401座椅-5S5 PC 1 160,89

3842510402底座-5S5 PC 1 29,77

3842510403靠背-5S5 PC 1 80,63

3842510404靠背-5S5件1 216,27

3842510405外壳-5S5 PC 1 29,23

3842510406靠背杆-5S5 PC 1 29,77

3842510408防扭结保护-5S5 PC 1 7,74

3842510409辅助设备-5S5 PC 1 151,93

3842510445升降板160X160 5S7 PC 1 426,58

3842510446升降板160X240 5S7 PC 1 457,94

3842510450升降板240X240 5S7 PC 1 562,46

3842510451升降板240X320 5S7 PC 1 629,04

3842510452升降板240X400 5S7 PC 1 736,40

3842510455升降板320X400 5S7 PC 1 794,91

3842510456升降板320X480 5S7 PC 1 930,80

3842510577金属板盖1X370X154 BQ160 5S7 PC 1 30,80

3842510578金属板盖1X370X234 BQ240 5S7 PC 1 30,80

3842510579金属板盖1X370X314 BQ320 5S7 PC 1 35,78

BQ10580X38053金属板

3842510581金属板盖1X370X474 BQ480 5S7 PC 1 41,03

3842510582金属板盖1X370X494 5S7 PC 1 46,15

3842510583金属板盖1X370X154 BQ160 5S7 PC 1 57,98

3842510584金属板盖1X370X234 BQ240 5S7 PC 1 46,15

3842510585金属板盖1X370X314 BQ320 5S7 PC 1 46,15

3842510586金属板盖1X370X394 BQ400 5S7 PC 1 46,15

3842510587金属板盖1X370X474 BQ480 5S7 PC 1 44,94

3842510588金属板盖U31X174X31X1 L=440 5S7 PC 1 66,99

3842510589金属板盖U31X174X31X1 L=440 5S7 PC 1 66,99

3842510590金属板盖U31X245X31X1 L=440 5S7 PC 1 71,44

3842510591金属板盖U31X325X31X1 L=440 5S7 PC 1 95,50

3842510592金属板盖U31X405X31X1 L=440 5S7 PC 1 100,75

3842510657星形椅腿-5S5件1 88,63

3842510659靠背-5S5件1 177,83

3842510663盖1,5X152,5X284 5S7件8,83

3842510695盘头螺钉ISO7380-M8X20-10.9-VZ 5S7 PC 1 0,55

3842510713盖罩-5S5件1 5,74

3842510714盖-5S5 PC 1 7,61

3842510715平把手-5S5 PC 1 5,60

3842510716盖-5S5 PC 1 8,69

3842510717合成衬套-5S5 PC 1 2,81

3842510718盖-5S5 PC 1 21,24

3842510769滚筒LFR5201-12KDD 5S5 PC 1 30,00

3842510770 ECCE9 18IC螺栓D12X34,5 5S1 PC 1 15,32

3842510788轴密封圈C1-1002-N3571 5S7 PC 1 6,71

3842510956导柱D16X130 5S7 PC 1 37,12

3842510977减震器M10X1 5SC PC 1 110,99

3842510978减震器M14X1,5 5SD PC 1 253,32

3842510979减震器M20X1,5 5SC PC 1 170,40

3842511113盖管D25 L=39,5 5S7 PC 1 0,81

3842511292开槽弹簧销S3X18-1.8159-VSM12785 5S7 PC 1 0,81

3842511389驱动轴D=23X109,5 5SC PC 1 136,42

3842511707防静电罩5S5 PC 1 33,37

3842511744润滑油毡ERSATZTEILBAUGRUPPE 5S1 PC 1 48,97

3842511745润滑油毡ERSATZTEILBAUGRUPPE 5S1 PC 1 55,16

3842511896润滑脂TRIBOL5000 0,25L 5SG PC 1 21,90

3842511905主梁BQ160 5S7 PC 1 18,05

3842511906主梁BQ240 BL160 5S7 PC 1 86,50

3842511907主梁BQ320 BL160 5S7 PC 1 87,98

3842511908主梁BQ400 BL160 5S7 PC 1 99,28

3842511909主梁BQ480 BL160 5S7 PC 1 65,53

3842512292底座主体HP2 VORM。5S7 PC 1 246,76

3842512322侧板140X178,5条建议5S5 PC 1 25,72

3842512323侧板140X178,5连杆5S5 PC 1 25,72

3842512364停车门VE3/DD-100 5S7 PC 1 861,81

3842512367停车门VE3 5S7 PC 1 394,94

3842512373导向柱D25X394 5S7 PC 1 62,29

3842512374导向柱D25X439 5S7 PC 1 73,74

3842512375导向柱D25X489 5S7 PC 1 82,06

3842512376导向柱D25X539 5S7 PC 1 85,01

3842512377金属支架HP2 5S7 PC 1 37,00

3842512452同等零件套件HP 2 5S7 PC 1 385,83

3842512601抽屉S300 5S5 PC 1 205,60

3842512649驱动头AK-60 LE01 5S1 PC 1 234,66

3842512653张紧头SK-60 LE01 5S1 PC 1 153,00

3842512655张紧头SK-120 LE01 5S1 PC 1 419,82

3842512953踏板880X400X19 5S5 PC 1 96,14

3842512965盘头螺钉ISO7380-M8X16-10.9-VZ 5S7 PC 1 0,55

3842512968行星齿轮箱I=38,64 5S7 PC 1 2.939,68

3842513403提升板1800N 5S5 PC 1 1.025,19

3842513459块25X30X10 5S5 PC 1 17,62

3842513467 T形槽石L=20 BEARB。5S5件1 2,20

3842513560英尺M12 L=40 5S5件100 613,53

3842513867传动带D3 L=414 5S7 PC 1 10,11

3842513877对中螺栓D8/5 5S7 PC 1 0,10

3842514167紧固板-5S7 PC 1 100,75

3842514168导条15X20X100 5S7 PC 1 204,46

3842514169导杆D10X120 5S7 PC 1 71,03

3842514452齿带轮Z26 T5 5S7 PC 1 36,32

3842514582灯支架FASSUNG F.KOMPAKTL 5S5 PC 1 1,50

3842514657活塞密封件524934 5SC PC 1 12,11

3842514727平垫圈12270145 5S5 PC 1 1,37

3842514878节点板2X20GRAD 5S5 PC 1 27,92

3842514999多孔板1498X1198X2 QG W8T12 5S5 PC 1 161,59

3842515136六角轴EQ 0/T 5S7 PC 1 27,85

3842515137盖-5S7 PC 1 144,74

3842515156支撑板搁脚板B和5S7 PC 1 37,82

3842515164六角轴SW10 L=868 5S5 PC 100 1.041,96

3842515248悬挂装置8/10螺母5SC PC 1 4,18

3842515249悬挂装置8/10 FEDER 5SC PC 1 4,18

3842515250齿带25T5/630 A V 5S7 PC 1 71,84

3842515254齿带25T5/770 A V 5S7 PC 1 85,01

3842515255齿带25T5/920 A V 5S7 PC 1 98,34

3842515257齿带25T5/610 O E 5S7 PC 1 34,83

3842515258齿带25T5/690 O E 5S7 PC 1 46,41

3842515260齿带25T5/765 O E 5S7 PC 1 47,49

3842515262齿带25T5/840 O E 5S7 PC 1 56,10

3842515263齿带25T5/920 N V 5S7 PC 1 55,42

3842515265齿带25T5/630 N V 5S7 PC 1 56,90

3842515266齿带25T5/770 N V 5S7 PC 1 72,91

3842515308定心件6X8,6X10 5S1件1 0,11

3842515336停止20X26X7,5 5S7 PC 1 39,42

3842515492齿带轮30T5-26Z SW17I/SW17A 5S7 PC 1 30,80

3842515647踏板19X470X736 5S5 PC 1 58,03

3842515733偏辊D=36 5S7 PC 1 13,86

3842515758偏辊-5S7 PC 1 15,33

3842515844停车门VE 2/S 5S7 PC 1 93,98

3842515958停止34X20X60 5S7 PC 1 10,49

3842515971盲板3X290X540 M.BESCHR。5S5件1 44,29

3842516048提升板25X80X180 5S7 PC 1 117,03

3842516072张紧滚柱HQ2 5S7 PC 1 15,06

3842516124齿带轮36T5-26Z SW17I 5S7 PC 1 23,06

3842516156偏辊D38 SW17I 5S7 PC 1 21,40

3842516157齿带轮30T5-26Z SW17I 5S7 PC 1 21,66

3842516552偏辊-5S7 PC 1 13,74 12,69 12,35

3842516554扣环25SXN26-ZN 5S7 PC 1 1,21

3842516559皮带1,25X12 5S7 M 1 5,35

3842516565法兰头螺钉MLF-M8X12-10.9-VZ 5S7 PC 1 1,37

3842516575盖管D25 L=15 5S7 PC 1 3,63

3842516576盖管D25 L=95 5S7 PC 1 23,56

3842516579盖管D25 L=463,5 5S7 PC 1 59,87

3842516628盖管D25 L=37 5S7 PC 1 1,08

3842516632导向环D10 5S7 PC 1 1,09

3842516767齿形皮带轮D65,6X70 Z=42 AT5 5S7 PC 1 116,07

3842516769齿形滑轮AT5 B32 5S7 PC 1 30,41

3842516770偏辊D56X36,5 5S7 PC 1 57,33

3842516775夹销D12X80 5S7 PC 1 40,01

3842516778盖板72X72X1,5 5S7 PC 1 12,21

3842516781固定销D15X66 5S7 PC 1 25,84

3842516782螺栓D20X80 5S7 PC 1 23,66

3842516783螺栓D10X58 5S7 PC 1 18,44

3842516785导条-5S7 PC 1 6,86

3842516786夹紧件SW27X15 5S7 PC 1 23,95

3842516799隔套D13,9X7,8 5S7 PC 1 13,33

3842516804齿形皮带轮30T5-26Z SW17I 5S7 PC 1 28,52 27,1 26,38 25,66

3842516808刷子36X36 A=7,0MM 5S7 PC 1 5,64

3842516833偏辊D=30 5S7 PC 1 23,00 21,28 20,7

3842516836离合器SW17A/SW17A B=17,5 5S7 PC 1 20,31

3842516852外壳-5S7 PC 1 14,81

3842516853附件-5S7 PC 1 3,76

3842516854导向件-5S7 PC 1 1,60

3842516856盖管D25 L=115 5S7 PC 1 48,24

3842516882烧结金属衬套DIN1850-J32X40X20 5S5 PC 1 14,71

3842516884弹簧组TS2加5S7 PC 1 14,53

3842516894住宅基地BS2 A9 18IEB/UMLENKUNG 5S7 PC 1 23,64

3842516898导向件-5S7 PC 1 9,29

3842516899定位销D=5/5 L=13,5 5S7 PC 1 0,40

3842516900导向件-5S7 PC 1 2,69

3842516911偏辊D=38 SW17I 5S7 PC 1 27,25

3842516912轴D10X36 5S7 PC 1 3,76 3,49 3,38

3842516974法兰组件

3842517084盖管D25 L=55 5S7 PC 1 22,46

3842517104锁紧件>R<05.561.3653.1 5S5 PC 1 4,69

3842517156润滑油毡LF12 5S1 PC 1 23,15

3842517274盖板15X60X25 5S7 PC 1 35,62

3842517288塑料切割螺钉EJOT PT-WN1447-K100X和5S7 PC 1 1,37

3842517411摩擦垫圈GTM-1018-010 5S7 PC 1 2,16

3842517473导向件160 250,5X250,5X20 5S7件68,30

3842517474导向件240 330,5X330,5X20 5S7 PC 1 111,11

3842517475导向件320 410,5X410,5X20 5S7 PC 1 118,62

3842517476导板400490,5X490,5X20 5S7 PC 1 187,40

3842517478导向件90/160X160 5S7 PC 1 66,58

3842517479导向件90/240X160 BGR 5S7 PC 1 90,00

3842517480导向件90/240X160 5S7 PC 1 103,60

3842517485导向件180/160X160 A135 BGR 5S7 PC 1 130,00

3842517487导向件180/240X160 A135 BGR 5S7 PC 1 225,99

3842517488导向件180/240X160 A135 5S7 PC 1 108,15

3842517489导向件90/240X240 BGR 5S7 PC 1 112,73

3842517490导向件90/240X240 5S7 PC 1 106,13

3842517492导向件90/320X240 5S7 PC 1 110,45

3842517498导向件180/240X240/A135 5S7 PC 1 108,15

3842517502导向件90/320X320 5S7 PC 1 135,72

3842517504导向件180/320X320 A 90 5S7 PC 1 82,06

3842517506导向件180/320X320 A135 5S7 PC 1 118,65

3842517530轴颈M8，SW17X30 5S7 PC 1 21,66

3842517535导向件45 BG 5S7 PC 1 38,00

3842517544盖管D40 L=18 5S7 PC 1 16,36

3842517561法兰BG80 5S7 PC 1 104,18

3842517570离合器BG71 5S7 PC 1 64,33

3842517571离合器BG80 5S7 PC 1 64,33

3842517603法兰D77X20 5S7 PC 1 27,45

3842517613沉头螺钉S12X30 5S7 PC 100 141,79

3842517642板193X108X3 5S7 PC 1 25,01

3842517649偏辊D52X18 5S7 PC 1 65,38

3842517650轴颈SW17X18 M8 5S7 PC 1 28,39

3842517667摩擦垫圈GTM-0818-015 5S7 PC 1 1,87 1,75 1,71

3842517668塑料切割螺钉EJOT PT-WN1413-KA30X和5S7 PC 1 0,11

3842517669法兰头螺钉MLF-M5X12-10.9-VZ 5S7 PC 1 0,40

3842517670卡环SPI-47 5S7 PC 1 0,81

3842517853皮带罩EINLAUF 5S7 PC 1 3,31

3842517905驱动头AK 2 5S7 PC 1

3842517992电动机安装类型：3842507794 5S7邮编：1987,83

3842518011圆皮带D=10 L=865 5S7 PC 1 52,00

3842518028六角轴SW27 L=354,5 L1=170,6 5S7 PC 1 61,10

3842518029六角轴SW27 L=434,5 L1=250,6 5S7 PC 1 73,76

3842518030六角轴SW27 L=514,5 L1=330,6 5S7 PC 1 88,70

3842518031六角轴SW27 L=594,5 L1=410,6 5S7 PC 1 102,48

3842518032六角轴SW27 L=674,5 L1=490,6 5S7 PC 1 116,27

3842518033六角轴SW27 L=754,5 L1=569 5S7 PC 1 130,06

3842518034六角轴SW27 L=834,5 L1=650,6 5S7 PC 1 143,86

3842518036六角轴SW27 L=994,5 L1=810,6 5S7 PC 1 171,42

3842518039法兰-5S7 PC 1 110,56

3842518043导向件19X129X8 5S7 PC 1 4,03

3842518046异步电动机，3相220-415/50 440-480/60 5S7 PC 1 531,29

3842518048异步电动机，3相440/50 500/60 5S7 PC 1 531,29

3842518050异步电动机，3相220-415/50 440-480/60 5S7 PC 1 389,12 359,93 350,21 330,74

3842518051异步电动机，3相500/50 575/60 5S7 PC 1 389,12

3842518053异步电动机，3相200/346/50 208-240/60 5S7 PC 1 389,12

3842518058异步电动机，三相220-415/50 440-480/60 5S7 PC 1 369、04 341、37 332、14 313、68

3842518059异步电动机，3相500/50 575/60 5S7 PC 1 535,58

3842518060异步电动机，3相440/50 500/60 5S7 PC 1 390,43

3842518061异步电动机，3相200/346/50 208-360/60 5S7 PC 1 369,04

3842518096盖管D40 L=97,5 5S7 PC 1 22,46

3842518097盖管D40 L=137,5 5S7 PC 1 41,03

3842518107支柱20X5XL=245 A=225 5S7 PC 1 39,42

3842518108支柱20X5XL=325 A=305 5S7 PC 1 41,30

3842518109支柱20X5XL=405 A=385 5S7 PC 1 43,16

3842518110支柱20X5XL=485 A=465 5S7 PC 1 44,94

3842518111支柱20X5XL=565 A=545 5S7 PC 1 69,40

博世力士乐rexroth代理、力士乐上海经销商、博世力士乐电磁阀、力士乐rexroth选型资料，力士乐报价，rexroth销售价格，博世力士乐流量阀，博世比例阀，力士乐换向阀，rexroth液压泵，博世rexroth电磁换向阀，力士乐液压泵，博世bosch比例阀，力士乐rexroth液压泵，博世力士乐流量节流阀，博世bosch换向阀，博世液压阀，rexroth换向阀，力士乐代理，博世液压溢流阀，博世力士乐安全阀，bosch力士乐换向阀，博世比例阀，力士乐换向阀，博世力士乐比例阀，力士乐换向阀，力士乐比例阀，rexroth比例阀，力士乐换向阀，博世力士乐方向阀、博世BOSCH力士乐放大板、博世BOSCH力士乐液压泵、博世BOSCH力士乐液压阀、博世力士乐伺服产品