力士乐PV7叶片泵PV7-11/06-14RA01MA0-07

力士乐PV7叶片泵PV7-11/06-14RA01MA0-07 德国博世力士乐REXROTH叶片泵 液压油泵

库存大量REXROTH柱塞泵A10VSO,齿轮泵PGH4\5,PGF1/PGF2/PGF3,电磁阀4WE，电子变量泵SYDFEE-2X,电液比例控制阀0811,电液换向阀4WEH、4WE,减压阀DR10、DR20、叠加阀ZD、Z1S、Z2S,ZDR电磁溢流阀DBW，直动式溢流阀DBD、0532，先导溢流阀DB10、DB20,电磁球阀M-S、M-3S,力士乐电液比例控制阀\放大器、压力继电器0811，伺服驱动，电机

力士乐PV7叶片泵PV7-11/06-14RA01MA0-07

叶片泵特性

1.可在压力设定下具有自动高速流量及补偿功能，比定量叶片泵功率损耗少，发热低，是一种节省能源的率叶片泵，为系统设计工程师在率的回路中佳选择。

2.运转平衡安静，特别适合机床和室内的要求。

3.内含压力调整机构，系统可以不要调压阀并且适用直接式电动机，装配容易。

4.备有多种不同压力及流量范围，可供任意选择。

叶片泵使用要点

1.为了使叶片泵可靠地吸油，其转速在500～1500r/min的范围，转速太低时，叶片不能紧压定子的内表面和吸油；转速太高则造成泵的“吸空”现象，泵的工作不正常。油的粘度要选用适当，粘度太大，吸油阻力；油液过稀，间隙影响，真空度不够，会对吸油造成不良影响。

2.叶片泵对油中的污物很敏感，工作可靠性较差，油液不清会使叶片卡死，因此注意油液良好过滤和环境清洁。

3.因泵的叶片有安装倾角，故转子只允许单向旋转，不应反向使用，否则会使叶片折断。

双联叶片泵

单作用：叶片是镶嵌在槽里的，可以自由滑动，当旋转产生时，叶片在离心作用下甩到泵壳上，叶片泵是容积泵，相邻的两个叶片运动到下边时与泵壳和转子封闭的容积较小，在上边时较大，当转子顺时针转动时，相邻两叶片经历从较下边到较上边的过程就是容积加大过程，所以吸油（从第四象限到第二象限）；从较上到较下是容积减小过程，所以压油（从第二到第四象限）。

双作用：当电机带动转子沿转动时，叶片在离心力和叶片底部压力油的双重作用下向外伸出，其顶部紧贴在定子内表面上。处于四段同心圆弧上的四个叶片分别与转子外表面、定子内表面及两个配流盘组成四个密封工作油腔。这些油腔随着转子的转动，密封工作油腔产生由小到大或由大到小的变化，可以通过配流盘的吸油窗口（与吸油口相连）或排油窗口（与排油口相连）将油液吸入或压出。

PV7-11/06-14RA01MA0-07 德国博世力士乐REXROTH叶片泵设计标准

力士乐PV7叶片泵型号举例

REXROTH/力士乐叶片泵PV7-17/10-14RE01C0-16

结构 先导式变量叶片泵

型号 PV7

安装方式 4 孔法兰 (按 VMDA 24560 第 1 部分和 ISO 3019/2)

油口 管螺纹或 SAE 法兰接口 (取决于机型规格)

安装位置 任意，较好水平安装 (见 28 和 29 页)

轴负载 不能传递径向和轴向力

转向 右旋 (对着轴端看去)

驱动转速 n min–1 900 至 1800

机型规格 BG 10 16 25 40 63 100

排量 V

g cm3 14 20 20 30 30 45 45 71 71 94 118 150

驱动功率 1) P

max kW 6.3 5.8 8.5 6.8 13.7 10.2 20.5 16.5 33 20.9 51.5 33

允许的驱动转矩 T

max Nm 90 140 180 280 440 680

较大流量 2) qV l/min 21 29 29 43.5 43.5 66 66 104 108 136 171 218

在零行程时的泄漏流量

(在出口工作压力 = pmax时)

qVL l/min 2.7 1.9 4 2.5 5.3 3.2 6.5 4 8 5.3 11 7.3

工作压力，较好值

– 入口 pmin-max bar 0.8 至 2.5

– 出口 3) pmax bar 160 100 160 80 160 80 160 80 160 80 160 80

– 泄漏口 pmax bar 2

REXROTH/力士乐叶片泵PV7-17/10-14RE01C0-16?

压力液体

在 160 bar (额定压力) 以下应用时 HLP 矿物油，按 DIN 51524 第 2 部分

特殊压力液体 4)

– 至工作压力 pmax = 100 bar HETG 和 HEES 压力液体，按 VDMA 24 568

– 至工作压力 pmax = 80 bar HLP 矿物油，按 DIN 51524 第 2 部分 (从 100 mm2/s 起)

HL 矿物油，按 DIN 51524 第 1 部分

压力液体温度范围 ? °C –10 至 70，注意允许的粘度范围!

粘度范围 ν mm2/s 16 至 160，在工作温度时

较大 800，在供油运行起动时

较大 200，在零行程运行起动时

压力液体的较大允许污染度

洁净等级按照 ISO 4406 (c)

等级 20/18/15 5)

重量 (包括控制器) m kg 12.5 17 21 30 37 56

REXROTH/力士乐叶片泵PV7-17/10-14RE01C0-16?

流量变化

(在调节螺栓转一圈和

n = 1450 min–1 时) qV l/min 10 14 18 25 34 46

1) 在 n = 1450 min–1; p = pmax; ν = 41 mm2/s 时测量

2) 由于加工误差的原因，流量可能比给出的数值高出大

约 6 %

(在 n = 1450 min–1; p = 10 bar; ν = 41 mm2/s 时测量)。

3) 可设置的较小压力大约为 20 bar，出厂时标准化地设置为

30 bar。

4) 其它的特殊压力液体 (例如：用于在食品工业中应用的设备

或不易燃的液体) 请询问！

5) 在液压系统中必须保持针对部件所给出的洁净等级。有效

的过滤能防止故障，并同时提高部件的使用寿命。

滤油器的选择见样本 RC 50070,

REXROTH/力士乐叶片泵PV7-17/10-14RE01C0-16?

RC 50076, RC 50081, RC 50086 和 RC 50088。

力士乐叶片泵 常规供货型号

力士乐rexroth叶片泵

力士乐rexroth叶片泵PV7-17/10-20RE01MCO-10

力士乐rexroth叶片泵PV7-17/10-14RE01MCO-16

力士乐rexroth叶片泵PV7-1X/10-20RE01MCO-10-A497

力士乐rexroth叶片泵PV7-11/06-10RA01MA0-05

力士乐rexroth叶片泵PV7-1X/16-20RE01MC0-16

力士乐rexroth叶片泵PV7-1A/16-30RE01MCO-08

力士乐rexroth叶片泵PV7-2X/20-25 RA01MA0-10

力士乐rexroth叶片泵PV7-11/06-10RA01MA0-10 印度产

力士乐rexroth叶片泵PV7-17/10-14RE01MCO-16

力士乐rexroth叶片泵PV7-11/06-10RA01MA0-10

力士乐rexroth叶片泵PV7-17/10-14RE01C0-16

力士乐rexroth叶片泵PV7-17/10-20REO1MC0-08

力士乐rexroth叶片泵PV7-17/10-20REO1MC0-08

力士乐rexroth叶片泵PV7-20/20-25RA01MA0-05

力士乐rexroth叶片泵PV7-18/63-71RE07MC0-16

力士乐rexroth叶片泵PV7-19/40-71RE37MC0-08

力士乐rexroth叶片泵PV7-19/40-71RE37MC0-08

R900506808 力士乐rexroth叶片泵PV7-18/63-71RE07MC0-16

R900950954 力士乐rexroth叶片泵PV7-2X/20-25RA01MA0-05

力士乐rexroth叶片泵PV7-2X/20-25RA01MA0-05印度产

型号

力士乐rexroth叶片泵PV7-17/10-14RE01MCO-16

力士乐rexroth叶片泵PV7-17/10-14RE01MCO-16

力士乐rexroth叶片泵PV7-2X/20-20RA01MA0-10

力士乐rexroth叶片泵PV7-17/16-30REOMCO-08

力士乐rexroth叶片泵PV7-20/20-25RA01MAO-10

力士乐rexroth叶片泵PV7-1X/16-20

力士乐rexroth叶片泵PV7-1X/63-94

力士乐rexroth叶片泵PV7-1X/16-20

力士乐rexroth叶片泵PV7-1X/63-94

力士乐rexroth叶片泵PV7-1X/16-20

力士乐rexroth叶片泵PV7-1X/63-94

力士乐rexroth叶片泵PV7-1X/06-10RA01MA0-10

力士乐rexroth叶片泵PV7-16/16-30RE01MCO-08

力士乐rexroth叶片泵PV7-1X/40-45RE37MCO-16

力士乐rexroth叶片泵PV7-17/10-20RE01MCO-10

力士乐rexroth叶片泵PV7-1X/25-30RE10/MCO-16

力士乐rexroth叶片泵PV7-17/10-20RE01MCO-10 RV 250/

力士乐rexroth叶片泵PV7-17/10-20RE01MCO-10 RV 250/

力士乐rexroth叶片泵PV7-1X/06-10RA01MAC-10

力士乐rexroth叶片泵PV7-17/16-20REO1MCO-16

叶片泵出厂前在装配时，都是按着顺时针旋转方向组装的。不允许逆时针运转使用（从轴端观察〕。

叶片泵从结构上可分为车辆叶片泵、变量叶片泵和定量叶片泵、双级叶片泵以及双联叶片泵多种。安装方式基本为法兰安装式，而榆次液压件厂生产的叶片泵有脚架式的〔在订货时应注明）。 

力士乐rexroth叶片泵

PV7-17/10-20RE01MCO-10

PV7-17/10-14RE01MCO-16

R901292147 PV7-1X/10-20RE01MCO-10-A497

PV7-11/06-10RA01MA0-05

PV7-1X/16-20RE01MC0-16

PV7-1A/16-30RE01MCO-08

PV7-2X/20-25 RA01MA0-10

PV7-11/06-10RA01MA0-10 印度产

PV7-17/10-14RE01MCO-16

PV7-11/06-10RA01MA0-10

PV7-17/10-14RE01C0-16

PV7-17/10-20REO1MC0-08

PV7-17/10-20REO1MC0-08

PV7-20/20-25RA01MA0-05

PV7-18/63-71RE07MC0-16

PV7-19/40-71RE37MC0-08

PV7-19/40-71RE37MC0-08

R900506808 PV7-18/63-71RE07MC0-16

R900950954 PV7-2X/20-25RA01MA0-05

PV7-2X/20-25RA01MA0-05印度产

型号

PV7-17/10-14RE01MCO-16

PV7-17/10-14RE01MCO-16

PV7-2X/20-20RA01MA0-10

PV7-17/16-30REOMCO-08

PV7-20/20-25RA01MAO-10

PV7-1X/16-20

PV7-1X/63-94

PV7-1X/16-20

PV7-1X/63-94

PV7-1X/16-20

PV7-1X/63-94

PV7-1X/06-10RA01MA0-10

PV7-16/16-30RE01MCO-08

PV7-1X/40-45RE37MCO-16

PV7-17/10-20RE01MCO-10

PV7-1X/25-30RE10/MCO-16

PV7-17/10-20RE01MCO-10 RV 250/

PV7-17/10-20RE01MCO-10 RV 250/

PV7-1X/06-10RA01MAC-10

PV7-17/16-20REO1MCO-16

叶片泵的吸油滤油器，应采用泵流量的两倍以上，允许吸人真空度不大于0.013Mpa。在系统中的回油管路上，应设置过滤精度不大于20~30μm的回油滤油器，当新安装的系统工作10~20h后，可将回油滤油器拆开，取出滤芯，其内部有氧化皮、电焊渣、铁屑、砂粒和橡胶碎块等杂质，这些杂物是安装系统时未清理净的或液压件内部存留的，经压力的振动和流体的冲击而集中在回油滤油器内，若无回油滤油器时，则全部集中在油箱下部。

R900701362 PV7-1X/40-45RE37KD0-16

R900700384 PV7-1X/40-45RE37MW0-16WH

R900598753 PV7-1X/10-14RE01MC3-16

R900593330 PV7-1X/40-45RE37MD0-16

R900592237 PV7-1X/16-20RE01MC3-16

R900590087 PV7-1X/40-45RE37MC3-16

R900586235 PV7-1X/25-30RE01MC3-16

R900580384 PV7-1X/40-45RE37MC0-16

R900580383 PV7-1X/25-30RE01MC0-16

R900580382 PV7-1X/16-20RE01MC0-16

R900580381 PV7-1X/10-14RE01MC0-16

R900576487 PV7-1X/25-45RE01MC5-08WH

R900574560 PV7-1X/63-94RE07MD0-08

R900573212 PV7-1X/16-20RE01MD0-16-A234

R900571305 PV7-1X/63-71RE07KC0-16

R900568873 PV7-1X/100-150RE07KC0-08

R900568833 PV7-1X/25-45RE01MD0-08

R900564746 PV7-1X/06-10RA01MA3-10

R900563233 PV7-1X/06-10RA01MA0-10

R900562475 PV7-1X/25-30RE01KC0-16

R900561857 PV7-1X/06-10RA01MA0-05

R900561846 PV7-1X/100-150RE07MC0-08

R900561581 PV7-1X/40-71RE37MC3-08

R900560916 PV7-1X/10-14RE01KC0-16

R900560659 PV7-1X/63-94RE07MC0-08

R900560658 PV7-1X/16-30RE01MD0-08

R900560629 PV7-1X/100-150RE07MC5-08

R900556803 PV7-1X/100-118RE07MC5-16WH

R900553692 PV7-1X/63-71RE07MC5-16WG

R900553588 PV7-1X/40-45RE37MC5-16WH

R900551273 PV7-1X/25-45RE01MC7-08

R900551051 ABHAG-0160S43/PV7-16-30/112M/S /S02G781A

R900548512 PV7-1X/10-14RE01MD0-16-A234

R900546887 PV7-1X/63-71RE07KC3-16

R900546886 PV7-1X/25-30RE01KC3-16

R900539886 PV7-1X/40-71RE37MD0-08

R900538525 PV7-1X/25-45RE01MC3-08

R900538125 PV7-1X/10-20RE01MC3-10

R900537419 PV7-1X/10-14RE01MN0-16

R900534508 PV7-1X/25-45RE01MC0-08

R900534412 PV7-1X/16-20RE01MC7-16

R900534143 PV7-1X/10-20RE01MC0-10

R900533851 PV7-1X/10-14RE01MC0-16-A184

R900533637 PV7-1X/100-118RE07MC7-16

R900533582 PV7-1X/16-30RE01MC0-08

R900533296 PV7-1X/16-30RE01MC3-08

R900532770 PV7-1X/100-118RE07MD0-16

R900535588 PV7-1X/40-71RE37MC0-08

R900535532 PV7-1X/25-45RE01MC5-08

R900523597 PV7-1X/40-45RE37KC0-16

R900520787 PV7-1X/10-14RE01MD5-16

R900520401 PV7-1X/10-14RE01MC5-16

R900519094 PV7-1X/63-71RE07MD0-16

R900518218 PV7-1X/63-71RE07MC5-16

R900517795 PV7-1X/16-20RE01MC0-16-A184

R900517464 PV7-1X/25-30RE01MC5-16

R900516546 PV7-1X/100-118RE07MC5-16

R900511986 PV7-1X/63-71RE07MC3-16

R900511215 PV7-1X/100-118RE07MC3-16

R900509506 PV7-1X/25-30RE01MD0-16

R900509274 PV7-1X/16-20RE01MD0-16

R900509053 PV7-1X/10-14RE01MC7-16

R900506809 PV7-1X/100-118RE07MC0-16

R900506808 PV7-1X/63-71RE07MC0-16

R900506473 PV7-1X/16-20RE01MC5-16

R900504653 PV7-1X/10-14RE01MD0-16

R900502277 PV7-1X/40-45RE37MC5-16

R901134661 PV7-1X/16-20RE01MD6-16

R901133981 PV7-1X/63-71RE07MC3-06-A460

R901129340 PV7-1X/100-118RE07MW6-16WH

R901081778 PV7-1X/06-14RA01MA0-10-A452

R901065655 PV7-1X/06-10RA01KA0-05

R901064326 PV7-1X/40-55RE37MC0-08-A449

R901061279 PV7-1X/100-118RE07MW0-16WG

R901059512 PV7-1X/40-71RE37MW0-08WH

R901055473 PV7-1X/40-45RE37MW0-16WG

R901049299 ABAPG-PV7-118D0 10SO18DRG/225S-4-B0/SEFR

R901047776 PV7-1X/40-45RE37MC0-16-A446

R901047606 PV7-1X/06-10RA01KA0-10

R901043560 PV7-1X/10-20RE01MW0-10WH

R901032005 PV7-1X/40-45RE37MC7-16WG

R901026649 PV7-1X/06-10RA01MA0-10-A441

R901022287 PV7-1X/25-30RE01MN0-16

R901021722 PV7-1X/63-71RE07KW0-16WG

R901017159 PV7-1X/63-71RE07MW0-16WH

R900979440 PV7-1X/40-45RE37MW0-16

R900978121 PV7-1X/06-10RE01MA3-10

R900976176 PV7-1X/25-45RE01MN0-08

R900976100 PV7-1X/63-71RE07MC6-16

R900973308 PV7-1X/06-14RA01MA0-07-A399

R900973306 PV7-1X/06-14RA01MA0-04-A399

R900964375 PV7-1X/06-14RE01MA3-07

R900963916 PV7-1X/06-10RA01MA0-10-A501

R900961521 PV7-1X/100-118RE07MC6-16

R900959317 PV7-1X/40-45RE37MC7-16

R900958306 PV7-1X/06-14RE01MA0-07

R900954137 PV7-1X/40-45RE37MC6-16

R900952282 PV7-1X/06-14RA01MA3-07

R900950419 PV7-1X/100-118RE07MD0-16-A234

R900950061 PV7-1X/100-118RE07MC5-16WG

R900949187 PV7-1X/100-118RE07MD6-16

R900948299 PV7-1X/100-150RE07MC5-08WH

R900946174 PV7-1X/40-45RE37MC0-16-A276

R900942455 PV7-1X/63-71RE07MC5-16WH

R900941073 PV7-1X/10-14RE01MC0-16-A268

R900941071 PV7-1X/10-14RE01MC0-16-A267

R900939159 PV7-1X/16-20RE01MN0-16

R900937407 PV7-1X/100-150RE07KD0-08

R900936326 PV7-1X/06-10RE01MA0-05

R900935443 PV7-1X/40-45RE37MC3-16-A184

R900933324 PV7-1X/10-14RE01MC5-16WH

R900933323 PV7-1X/25-30RE01MC5-16WH

R900931321 PV7-1X/06-14RA01MA0-04-A257

R900930060 PV7-1X/10-14RE01MC0-16-A202

R900928704 PV7-1X/100-118RE07MN0-16

R900926429 PV7-1X/16-20RE01MC5-16 WH

R900925956 PV7-1X/63-71RE07MD0-16-A234

R900922602 PV7-1X/40-45RE37MD0-16-A234

R900920233 PV7-1X/16-20RE01MC0-16-A17

R900919237 PV7-1X/06-14RA01MA0-07

R900919235 PV7-1X/06-14RA01MA0-04

R900916201 PV7-1X/10-20RE01KC0-10

R900915470 PV7-1X/100-150RE07MD0-08

R900910480 PV7-1X/63-71RE07MD5-16

R900910479 PV7-1X/100-150RE07MD5-08

R900910016 PV7-1X/40-45RE37MC5-16WG

R900906584 PV7-1X/10-20RE01MD0-10

R900903108 PV7-1X/06-10RE01MA0-10

R900891727 DICHTUNGSSATZ V3-4X/12 PV7-1X/06V

R900891726 DICHTUNGSSATZ V3-4X/12 PV7-1X/06M

R900891725 DICHTUNGSSATZ V3-4X/25 PV7-1X/20V

R900891724 DICHTUNGSSATZ V3-4X/25 PV7-1X/20M

R900891704 DICHTUNGSSATZ PV7-1X/10M

R900891703 DICHTUNGSSATZ PV7-1X/16M

R900891702 DICHTUNGSSATZ PV7-1X/25M

R900891701 DICHTUNGSSATZ PV7-1X/40M

R900891700 DICHTUNGSSATZ PV7-1X/63M

R900891699 DICHTUNGSSATZ PV7-1X/100M

R900780016 PV7-1X/25-45RE01MW0-08WH

R900772792 PV7-1X/10-14RE01MW0-16

R900771631 PV7-1X/100-118RE07MD0-16-A427

R900768658 PV7-1X/25-30RE01MW0-16

R900763234 ABKAG-60AL9/PV7-10/90L-4-A1/NL/012B60高等1

R900761807 PV7-1X/100-150RE07MC5-08WG

R900751356 PV7-1X/25-45RE01MC7-08WG

R900750169 PV7-1X/63-71RE07MD6-16

R900744715 PV7-1X/63-71RE07MN0-16

R900744495 PV7-1X/25-30RE01MW0-16WH

R900740824 PV7-1X/100-118RE07MW0-16WH

R900738663 PV7-1X/10-20RE01MC5-10WG

R900733271 PV7-1X/63-71RE07MW0-16

R900729468 PV7-1X/10-14RE01KD0-16

R900720730 PV7-1X/63-71RE07MC0-16-A234

R900711250 PV7-1X/40-71RE37MC5-08WH

R900705106 PV7-1X/63-71RE07MC7-16WH

R900919237 PV7-1X/06-14RA01MA0-07

R900910016 PV7-1X/40-45RE37MC5-16WG

R900247239 PV7-1X/10-20RE01MC5-10WH

R900245924 PV7-1X/16-30RE01MC5-08WH

R900891703 SEAL KIT PV7-1X/16M

R900598753 PV7-1X/10-14RE01MC3-16

R900590087 PV7-1X/40-45RE37MC3-16

R900580384 PV7-1X/40-45RE37MC0-16

R900580383 PV7-1X/25-30RE01MC0-16

R900580382 PV7-1X/16-20RE01MC0-16

R900580381 PV7-1X/10-14RE01MC0-16

R900573212 PV7-1X/16-20RE01MD0-16-A234

R900563233 PV7-1X/06-10RA01MA0-10

R900560659 PV7-1X/63-94RE07MC0-08

R900535588 PV7-1X/40-71RE37MC0-08

R900534143 PV7-1X/10-20RE01MC0-10

R900533582 PV7-1X/16-30RE01MC0-08

R900506809 PV7-1X/100-118RE07MC0-16

R900506808 PV7-1X/63-71RE07MC0-16

R900504653 PV7-1X/10-14RE01MD0-16

液压油箱在液压系统中的主要作用为储油、散热、分离油中所含空气及泡沫。选用油箱首先要考虑其容

量，一般移动式设备取泵大流量的2～3倍，固定式设备取3～4倍；其次考虑油箱油位，当系统全部液压油缸伸出后油箱油面不得低于低油位，当油缸回缩以后油面不得高于高油位；后考虑油箱结构，传统油箱内的隔板并不能起沉淀脏物的作用，应沿油箱纵轴线安装一个垂直隔板。此隔板一端和油箱端板之间留有空位使隔板两边空间连通，液压泵的进出油口布置在不连通的一端隔板两侧，使进油和回油之间的距离远，液压油箱多起一些散热作用。